Table of Contents
Related Manuals for Axon EZ-Seal
Summary of Contents for Axon EZ-Seal
- Page 1 AXON CORPORATION – EZ-SEAL August 21, 2001 HEAT SHRINK TUNNEL CONVECTIVE (BR/SR Models) & RADIANT (IR Models) OPERATOR’S MANUAL MODEL PART NUMBER SERIAL # 1341 Express Drive, Raleigh, NC, USA 27603 Phone (919) 772-8383 http://www.axoncorp.com Fax (919) 772-5575...
-
Page 2: Table Of Contents
AXON CORPORATION – EZ-SEAL August 21, 2001 TABLE OF CONTENTS SECTION CONTENT PAGE NUMBER Warranty Company History Introduction Customer Service Specifications Message Conventions Safety Precautions Installation Main Components Sequence of Operation Appendix A Spare Parts Appendix B Troubleshooting 1341 Express Drive, Raleigh, NC, USA 27603 Phone (919) 772-8383 http://www.axoncorp.com... -
Page 3: Warranty
Page 1 Warranty Axon Corporation (Seller) warrants its machines to be free from defects in material and workmanship for a period of twelve (12) months after the date of shipment. Any part, which proves to be defective during normal use and service, will be repaired or replaced with a new or functionally operative part, free of shipping charges. -
Page 4: Introduction
Axon offers a range of machine speeds and sizes to meet the needs of a wide range of customers, from the smallest startup business to the largest multi national manufacturers. -
Page 5: Specifications
24” 10” Weight (lbs) Notes: 1 – Custom Tunnel opening sizes are available contact Axon Corporation. 2 – Length of the EZ-48 and EZ-72 increase by 2” when conveyor mounted with Auto Tunnel Lift option. 3 – Width of the tunnel can be increased to accommodate larger products. -
Page 6: Message Conventions
AXON CORPORATION – EZ-SEAL August 21, 2001 Page 4 MESSAGE CONVENTIONS DANGER - Signifies an operator action or specific equipment area that can result in serious injury or death if proper precautions are not taken. WARNING – Signifies a operator action or specific equipment area the can result in personal injury if proper precautions are not taken. -
Page 7: Safety Precautions
Please refer to this manual for information regarding spare parts. If CAUTION there is any doubt, please call Axon Corporation. Good Housekeeping is a good safety practice and aids in improving machine efficiency. Keep the machine and area around the machine clean at all times. -
Page 8: Installation
Locate the box containing the EZ-Seal Heat Shrink Tunnel near its final location if space permits to minimize the amount of handling required. The EZ-Seal machine is heavy. Follow safe lifting procedures when handling the tunnel. -
Page 9: Main Components
AXON CORPORATION – EZ-SEAL August 21, 2001 Page 7 EZ-SEAL HEAT TUNNEL MAIN COMPONENTS CONVECTIVE (BR/SR Models) The Convective style Heat Shrink Tunnel has the following main components: 1. Temperature Controller (1128) – The temperature controller monitors a thermocouple and controls power to the heater elements to maintain the set temperature. -
Page 10: Sequence Of Operation
AXON CORPORATION – EZ-SEAL August 21, 2001 Page 8 EZ-SEAL HEAT SHRINK TUNNEL SEQUENCE OF OPERATION Prior to operating the tunnel perform a visual inspection of the exterior and heating portion of the tunnel. Check for loose bands which may be blocking air flow. If any problems are noted do not operate the tunnel until it has be inspected/repaired by qualified personnel. - Page 11 AXON CORPORATION – EZ-SEAL August 21, 2001 Page A1 REPLACEMENT PARTS EZ-SEAL 24, 36, 48, 72 Description Part Number CONVECTIVE (BR/SR Models) Blower Motor 1057 Temperature Controller 1/16 Din 1128 Thermocouple 1031 Snap Switch 1089 Blower Wheel, Lower 3052 Blower Wheel, Upper...
-
Page 12: Troubleshooting
AXON CORPORATION – EZ-SEAL August 21, 2001 Page B1 TROUBLESHOOTING Tunnel Does Not Reach Desired Temperature: Check that the appropriate voltage is being supplied to the tunnel. Check the distance between the tunnel and conveyor. Should this distance be more than 3” and the ambient room temperature is below 65 degrees Fahrenheit, baffles may be needed to contain the hot air and reduce the amount of ambient room temperature air from being drawn into the tunnel.
Need help?
Do you have a question about the EZ-Seal and is the answer not in the manual?
Questions and answers