Wireless Cooking Sensor; Basic Settings - Bosch PXY8 D Series User Manual

Fry with a large amount of oil
Use the lid to heat the oil, and remove it to fry the food.
Meat
Chicken pieces
Meatballs
Fish
Fish, breaded, battered
Vegetables and legumes
Vegetables, breaded, battered
Mushrooms, breaded or
battered
Desserts
Jam-filled doughnuts and
doughnuts
Frozen products
Chips
16.3 Wireless cooking sensor
To use PerfectCook Sensor, you must purchase a wire-
less cooking sensor.
You can purchase the wireless cooking sensor from
customer service, in our online shop or in a specialist
shop www.bosch-home.com.
Connecting the wireless cooking sensor
To connect the wireless cooking sensor to the control
panel, proceed as follows:
Select the basic setting ​ ⁠ ​ ⁠ ​ ⁠ . Basic settings
1.
→ Page 20
​ ⁠ lights up.
a
Select the cooking zone whose display lights up. A
2.
signal tone sounds.
3. Briefly press the centre of the wireless cooking
sensor within 30 seconds.
After a few seconds, the status of the connection
‒
between the cooking sensor and the control
panel appears on the cooking zone's visual dis-
play.
Result
​ ⁠ Connected PerfectCook Sensor is available.
correctly
​ ⁠ Not con- Communication error
nected cor- ¡ Repeat the connection process.
rectly If the result is still ​ ⁠ , contact
customer service.
17 Wireless cooking sensor
To use PerfectCook Sensor, you must purchase a wire-
less cooking sensor.
You can purchase the wireless cooking sensor from
customer service, in our online shop or in a specialist
shop www.bosch-home.com.
​ ⁠
180 10-15
180 10-15
180 10-15
180 4-8
180 4-8
180 5-10
180 4-8
​ ⁠ flashes.
Result
​ ⁠ Not con-
nected cor-
​ ⁠
rectly
Resetting the wireless cooking sensor
Press the centre of the cooking sensor for approx. 8
1.
- 10 seconds.
a During this process, the LED display for the wireless
cooking sensor lights up three times.
a When the LED lights up for the third time, it will start
to reset the temperature sensor.
Now stop pressing the centre of the wireless cook-
2.
ing sensor.
a As soon as the LED goes out, this means that the
wireless cooking sensor has been reset.
Repeat the connection process from point 2.
3.
Setting the boiling point
The point at which water starts to boil depends on the
height of your home above sea level. If the water is
boiling too vigorously or not vigorously enough, you
can adjust the boiling point. Proceed as follows:
Select the basic setting ​ ⁠ ​ ⁠ . Basic settings → Page 20
Height
0 m
100 - 200 m
200 - 400 m
400 - 600 m
600 - 800 m
800 - 1000 m
1000 - 1200 m
1200 - 1400 m
Over 1400 m
1 Basic setting
Note: The temperature of 3/100 ºC is sufficient to cook
efficiently but, to set more intensive cooking, a lower
level can be selected.
17.1 Scope of delivery
After unpacking all of the parts, check for any transport
damage and for completeness of delivery.
​ ⁠ Wireless cooking sensor
¡
​ ⁠ Silicone patch
¡
Wireless cooking sensor en
Communication error
¡ Bluetooth communication error.
Repeat the connection process.
¡ You have not pressed the
centre of the wireless cooking
sensor within 30 seconds of se-
lecting the cooking zone. Re-
peat the connection process.
¡ The battery in the wireless
cooking sensor is flat. Replace
the battery, reset the wireless
cooking sensor and repeat the
connection process.
Setting value ​ ⁠ ​ ⁠
​ ⁠
​ ⁠
1
​ ⁠
​ ⁠
​ ⁠
​ ⁠
​ ⁠
​ ⁠
​ ⁠
17