Advertisement
Device Installation/ 设备安装
A SD Card Installation/ 安装 SD 卡
Use the
Phillips screwdriver
to remove the
transparent
SD card. You can refer to the SD card icon on the maintenance window for the
insertion direction.
使用十字螺丝刀将透明罩卸下，插入 SD 卡，SD 卡插入方向参考维护窗上标识。
When the camera is not or
cannot be connected to a video
security platform for a long
time, you are advised to disable
video buffering to increase the
service life of the SD card.
若摄像机长时间无法接通平台或者不
对接平台使用，建议手动关闭摄像机
的平台离线缓存补录功能，以提高 SD
卡的使用寿命。
Connect the cables to the tails of the camera, perform insulation
3
operations on the cables (see
the cables through the cable entry on the wall(To route cables from the
side, use a Phillips screwdriver to open the cable outlet on the side). Use
the torque of 5 to 7 kgf.cm to fasten the tapping screws.
将线缆与摄像机的尾线连接，对线缆进行绝缘处理（参见"防水绝缘处理"），
然后塞入墙壁出线孔（如果要从侧方走线，请用十字螺丝刀打开图中标红的侧
方出线口出线）。使用 5~7Kgf.cm 的扭矩拧紧自攻螺钉。
The cable outlet on the side
侧方出线口
NOTE/ 说明
Before the camera is
fixed, cable connection
and waterproof insulation
treatment should be done
first. See "Cable Connection"
and "Waterproofing and
Insulation".
摄像机在固定前，请先做好线缆
连接和防水绝缘处理，参见 " 连
接线缆 " 和"防水绝缘处理"。
B Surface-mounted Installation/ 吸顶安装
cover, and install the
Paste the drilling sticker in the camera installation position and
1
ensure that the center of the sticker overlaps the center of the cable
outlet on the wall. Obtain a drill bit with a 5 mm diameter and drill
four 40 mm holes in the specified positions marked by the stickers.
Use a claw hammer to install an expansion bolt into the hole.
将安装定位贴纸贴在摄像机安装位置，贴纸中心请对准墙壁出线孔。依照贴
CAUTION/ 注意
纸上的标注，选择直径为 5mm 的钻头，钻取深约 40mm 的导孔，并使用
羊角锤将膨胀螺栓打入钻好的孔内。
This camera adopts the three-axis design, supporting a pan angle of
4
±175° , tilt angle of 0 to 75° , and role angle of ±175° .
), and put
Use a Phillips screwdriver to loosen screws on the chipset, and adjust
the shooting angle. After the adjustment is complete, tighten the
screws on the chipset. After the adjustment is complete, tighten the
screws on the chipset.
该款摄像机为三轴工艺设计，水平方向可转动 ±175°，垂直方向可转动
0~75° ，机芯可以转动 ±175° ，适应不同角度的安装。使用十字螺丝刀将
固定机芯的螺丝拧松，调整检测角度，调整完毕后，拧紧固定机芯的螺丝。
Use a Phillips screwdriver to remove the transparent cover, lightly press
2
the inner cover without blocking the two holes, and remove the inner
cover.
使用十字螺丝刀卸下透明罩，然后双指轻压内罩非固定卡扣位置，卸下内罩。
Lightly press the inner cover, and fix it to the chipset. Then align the
5
transparent cover with the base through the tapped holes, close the
transparent cover, and use a Phillips screwdriver to tighten the screws.
双指轻压内罩，将内罩卡槽对准卡扣，固定内罩，然后将透明罩和底座的螺孔
位置对齐，合上透明罩并使用十字螺丝刀拧紧螺钉。
4
Position outside
of the buckle
非固定卡扣位置
Advertisement
