Related Manuals for Supertech agroline Superpro
Summary of Contents for Supertech agroline Superpro
- Page 1 Superpro User Manual Instruction manual Bedienungsanleitung Notice d’utilisation Manuale di Istruzioni Gebruiksaanwijzing Bruksanvisning Instrucciones de uso Instrukcja obsługi Ver 1.1.0 Page 1/13...
-
Page 2: Table Of Contents
Introduction Package Content Part Locator Keypad Instructions Prepare and Make a Measurement Adjusting the Calibration of the Meter Superpro Settings and Menu´s MEASURE BATTERY CLEAR AVERAGE CALIBRATION Some more valuable information about the moisture meter Using the averaging facility Battery... -
Page 3: User Information
User Information Warning/ Danger symbols used in this User Manual: These notes identify hazards which have a high probability of resulting in death or serious physical injury if not avoided. These notes identify hazards that can result in moderate or mild injuries if not avoided. These notes identify hazards associated with the risk of material damage. -
Page 4: Highlights & Features
It is an accurate instrument that provides consistent repeat readings when several samples are taken. The Superpro is made to ensure long durability and has a bright display for easy outdoor reading. -
Page 5: Package Content
Package Content ● Superpro moisture analyser ● Operator’s manual ● Grinder handle with 9 and 11ml measuring cups ● Brush for cleaning grinder ● Battery ● Shockproof carrying case Part Locator 1. Grinder handle with 9-11ml measuring cups 2. Grinder housing/lower grinder cell 3. -
Page 6: Instructions
Instructions This section explains how to use the Superpro Prepare and Make a Measurement Inspect the two parts of the grinder cell to make sure they are clean and empty. If the temperature of the grain sample differs a great deal from that of the meter, e.g. when taking measurements directly from the dryer, it is recommended to preheat the meter as follows: a. - Page 7 Press ON/TEST immediately. A series of asterisks will appear across the screen, followed by the moisture reading. The analyser will take ~10sec to measure the moisture content and calculate the temperature compensation and hereafter display the result. A new reading can be made by emptying and cleaning the test cell and filling it with a new sample. Do not re-test the sample without first emptying and refilling.
-
Page 8: Adjusting The Calibration Of The Meter
2. Read the results on the result screen Adjusting the Calibration of the Meter Superpro is factory calibrated for every crop using the official methods of measuring moisture content as compiled by ISTA (International Seed Testing Association). The calibration scales are compiled using samples of crops grown in normal conditions. -
Page 9: Superpro Settings And Menu´s
Superpro Settings and Menu´s The Superpro has a number of settings that can be reached by doing the following: 1. TURN ON DEVICE 2. Use the arrow-keys to choose between the menu settings The device have four menus: MEASURE The menu measure is used to choose the crop to be tested. -
Page 10: Battery
Auto Turn OFF time - Setting Our Superpro is pre programmed to Turn-OFF after approximately 90 seconds of inactivity. If the device turns off by itself while using it please turn on the meter by pressing ON/TEST. -
Page 11: Quick Guide To Display Messages
and moisture contents can now be read off the y-axis for any Bit value measured using subsequent samples of the same crop in the meter. Quick Guide to Display Messages Symbol: Definition: Calibration has been adjusted from the factory setting for the crop being displayed. Temperature ++ Grain temperature is above the upper operating limit (50°C). -
Page 12: Eu Weee Statement
Supertech Agroline Aps. Maltgørervej 7 5471 Søndersø, Denmark Declares Superpro to be in conformity with the requirements of the, Electromagnetic Compatibility (EMC Directive - 2014/30/EU and RoHS Directive - 2011/65/EU A signed Declaration Of Conformity document is available online at supertechagroline.com...
Need help?
Do you have a question about the Superpro and is the answer not in the manual?
Questions and answers