Table of Contents
Advertisement
Quick Links
Ironwood FX 750
User Manual
general information.
technical specifi cations. safety considerations.
delivery and installation. inspection.
receiving the machine.
fences and fence assembly.
operation.
tool adjustments. noise reduction.
maintenance. troubleshooting.
periodic maintenance.
assembly.
safety guard assembly.
spindle height adjustment.
safety.
features.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ironwood FX 750
Summary of Contents for Ironwood FX 750
- Page 1 Ironwood FX 750 User Manual general information. features. technical specifi cations. safety considerations. delivery and installation. inspection. assembly. receiving the machine. safety guard assembly. fences and fence assembly. operation. spindle height adjustment. tool adjustments. noise reduction. maintenance. troubleshooting. safety. periodic maintenance.
-
Page 2: Table Of Contents
10.0 Troubleshooting ..............22 10.1 Electrical Diagram PLEASE REVIEW AND OBSERVE ALL SAFETY INFORMATION / DIRECTIVES BEFORE INSTALLING, OPERATING, OR PERFORMING MAINTENANCE ON THIS MACHINERY. Ironwood FX 750 | User Manual... -
Page 3: General Information
1.1 Thank You! 1.3 Features Thank you for your purchase of the Ironwood FX 750 Shaper. At • Cast iron, ground and polished table is designed for heavy Stiles Machinery, our goal is to ensure that you are fully satisfied with cutting operations. -
Page 4: Technical Specifications
230v (3 phase), 460v (3 phase) Amperage 18.5 (230v) / 9.2 (460v) Machine Weight 1,170 lbs. (531 kg.) Shipping Dimensions (L x W x H) 41" x 45" x 43" (1020mm x 1150mm x 1080mm) Ironwood FX 750 | User Manual... -
Page 5: Safety Considerations
For your safety, read these instructions thoroughly before you install WaRninG and operate this machine. Always have these instructions available Never use the FX 750 for purposes other than its intended use. Do at the machine for reference. not modify or remove any guards or other safety features. Improper... -
Page 6: Facility Preparation
2.3 Power accommodate the Ironwood FX 750. Follow these guidelines: WaRninG 2.1 Floor A licensed electrician must connect the FX 750 to the building power source. • The floor must be flat and level. • Do not using extension cords. -
Page 7: Delivery And Installation
If you do not intend to install the Ironwood Shaper immediately after delivery, store it in a protected, cool, and dry location. -
Page 8: Inspection
Save all containers and packing materials until you are satisfied Caution that your machine has arrived in good condition. If you discover the The FX 750 weighs 1,040 pounds. For this procedure, we machine is damaged after you’ve signed for delivery, immediately recommend using four people. -
Page 9: Pre-Operation Cleaning
To replace the rings, start with the outer ring. Align the locator pin on the bottom of the ring with the insert on the outer rim. Repeat for each ring. Ironwood FX 750 | User Manual... -
Page 10: Assembly
To reposition the complete fence assembly on the table, loosen the two locking handles, move the fence assembly to the desired position, and tighten the two locking handles. Fence assembly (front and back views). Outfeed fence Infeed fence Ironwood FX 750 | User Manual... - Page 11 Remove the two lock nuts and the notch. bevel washer from the other end of the draw bar. Draw bar threaded Carefully insert the draw bar and into spindle spindle down through the shaft. Ironwood FX 750 | User Manual...
-
Page 12: Cutter Head/Tooling
Stiles Machinery.) safety nut the spindle. TOOLS REQUIRED: Tooling • Spindle nut wrench attaches to Install the cutter head or other tooling on the spindle. the spindle. Ironwood FX 750 | User Manual... -
Page 13: Top Dust Cover
4.5 Safety Guard Assembly Mitre gauge assembly. WaRninG Always use the safety guard assembly and hold-down when operating the FX 750. Select and adjust the safety guard to the tooling currently being used. Mitre gauge PARTS REQUIRED: bar. • Safety guard assembly TOOLS REQUIRED: •... -
Page 14: Connect To Power
Proper wiring inside the terminal strip box Remove terminal box cover. Remove the clear plastic insulator that covers the terminals. Connect power and grounding wires. Ironwood FX 750 | User Manual... -
Page 15: Safety
Like all power equipment, there is danger associated with the damage to your machine or personal injury. Always run at the Ironwood FX 750. Use caution and follow all safety instructions. correct speed and feed rate. Never force a tool or accessory to Take every precaution to protect yourself, others around you, and perform a job for which it was not designed. -
Page 16: Start The Machine
Turn on main power supply / connect the machine g. Turn power on to the machine. h. Repeat steps to check direction. Ironwood FX 750 | User Manual... -
Page 17: Operation
= 40 mm l = 160 mm b = 100 b = 100 b = 120 b = 120 b = 140 b = 140 b = 160 350 d (mm) 350 d (mm) Ironwood FX 750 | User Manual... -
Page 18: Speed Change And Belt Adjustment
Reminder: Always place the tool as close to the bottom of the Spindle spindle as possible. pulley The FX 750 machines are supplied with a 5-step motor pulley and a 5-step spindle pulley that provides spindle standard speeds of 3000, Motor 4000, 6000, 8000 and 10,000 RPM. -
Page 19: Spindle Height Adjustment
1mm or 2.5 mm indicated on the machine frame (sticker). Note: All Ironwood shapers accommodate Stiles power feeders. Tighten handwheel lock and spindle locking lever when desired Power ports are included on the rear of the machines. For more spindle height is obtained. -
Page 20: Positioning And Using Collars
8.8 Noise Reduction • Always use hearing protection. Table Workpiece is too small • Make sure tooling is in proper working condition. WRONG • Properly position material and guards. • Use proper tooling speed. Ironwood FX 750 | User Manual... -
Page 21: Maintenance
Every day. Clean spindle and main shaft with compressed air daily. Pulleys and Belts Monthly. Inspect for wear and proper tension. Table Surface Monthly. Wax table surface to prevent rust and lubricate for easy panel movement. Ironwood FX 750 | User Manual... -
Page 22: Troubleshooting
Sawdust, dirt or other debris stuck in raising Brush or blow out loose dust, dirt and other debris. mechanisms. Worn shaft/gear/sleeve worn. Call Stiles service. If you cannot resolve your issue, contact Stiles technical support at 616.698.6615. Ironwood FX 750 | User Manual... -
Page 23: Electrical Diagram
10.1 Electrical Diagram Ironwood FX 750 | User Manual... - Page 24 Stiles Machinery Inc. 3965 44th St. SE Version A Grand Rapids, MI 49512 September 2013 p. 616.698.7500 f. 616.698.9411 © 2013 Stiles Machinery Inc. www.stilesmachinery.com...
Need help?
Do you have a question about the FX 750 and is the answer not in the manual?
Questions and answers