Table of Contents
Related Manuals for protech SORADIO
Summary of Contents for protech SORADIO
- Page 1 SORADIO SORADIO Installation instructions - Pages 2-15 529 VISTA BLVD 89434 SPARKS, NV - USA Toll Free: 1-800-498-9662 / Phone: (775) 856-7333 / Fax: (775) 856-7658 Website: E-mail: www.protechusa.com sales@protechusa.com...
- Page 2 PROTECH SORADIO...
-
Page 3: Table Of Contents
User settings ........................5 Event log ..........................7 Network settings ........................ 8 RADIO CONFIGURATION ................9 Configuration using the CONNECT RADIO COORDINATOR ........... 9 Activate the radio on the SORADIO ................. 11 MAINTENANCE ....................12 TECHNICAL SPECIFICATIONS ..............12 PRODUCT REFERENCES ................13... -
Page 4: Wiring
* LEDs status L1, L2 et L3: L1: green Operating mode OFF: Radio Mode LEDs active only if BLE ON: RS485 Mode (unused in SORADIO) is activated after a short L2: orange Radio configuration Blinking: Radio mode not configured press on the tamper... -
Page 5: Smartphone Application
Authorize activation of Bluetooth if requested to do so by the application. 3. Press the tamper switch very briefly (1s) to activate the BLE connection of the SORADIO. Note: the connection remains active as long as the SORADIO is connected to the smartphone application. -
Page 6: Settings
PROTECH SORADIO 5. Click on the product found. SORADIO found Radio ID of the SORADIO found identical to the sticker on the card. 2.1 Settings Setting the time on the module Enter the module name: Click on the name to change and Save 2.2 Input status... -
Page 7: Input Settings
PROTECH SORADIO 2.3 Input settings Each input can be: • Enable / disable input. • Eject input. To apply the changes, click Save. Select Input disable input Eject input Not used Enable input Input disabled Input enabled Eject input Input not ejected Input ejected Note: It is only possible to eject an input if it is enable. - Page 8 PROTECH SORADIO 2.4.2 Applying an existing user setting Select the settings to load Click on “Apply configuration” By default, the application offers the following setting options: → SO-BEAM S RX (FR) → SO-BEAM M/L/XL Mixed (FR) → SO-BEAM M/L/XL TX (FR) →...
-
Page 9: Event Log
PROTECH SORADIO 2.5 Event log 1. Click on Menu Menu 2. Click on Event log Event log 3. View event log Date/Time of the event Type of events Input name List of events: − Alarm − End Alarm − Eject −... -
Page 10: Network Settings
2.6 Network settings 1. Click on Menu Menu 2. Click Network settings Network Settings Indication that radio is active The black point "●" indicates that the SORADIO has no assigned channel. (configuration via coordinator not done) Default parameter unused in SORADIO... -
Page 11: Radio Configuration
SORADIO RADIO CONFIGURATION 3.1 Configuration using the CONNECT RADIO COORDINATOR 1. Enable radio, see §3.2.Activate the radio on the SORADIO. Note: By default, the radio is disabled. 2. Refer to manual CONNECT RADIO COORDINATOR NT400 to start radio search. 3. SORADIO settings and status from UNIVERSAL MAXIBUS A. - Page 12 Input disable = Relay associated forced in alarm Input ejected = Relay associated forced out alarm. E. Input State (Note: status not available in radio mode) No alarm Alarm Disable 4. SORADIO Event log Events Date Input ID Radio : Network ID Radio address List of "Events"...
-
Page 13: Activate The Radio On The Soradio
SORADIO 3.2 Activate the radio on the SORADIO Note: radio activation allows resetting the radio configuration on the SORADIO and switching to radio search (wait for pairing with the CONNECT RADIO COORDINATOR) 1. Disconnect the power supply on the SORADIO 2. -
Page 14: Maintenance
PROTECH SORADIO MAINTENANCE Failure Probable causes Solutions Input disabled Activate input. Permanent alarm Non-wired entry Check wiring. Input ejected Remove ejection from input Never alarm Press the tamper for at least 1 The smartphone application The BLE connection of the second. -
Page 15: Product References
This module has been approved under FCC part 15C 15.247. This modular transmitter is only FCC authorized for this specific rule part. - The module is limited to PROTECH / SORHEA installation only. - Page 16 Host Product Labeling: FCC Certification: The final end product must be labeled in visible area with the following: “Contains Transmitter Module FCC ID: QVA-SORADIO” ISED Certification: The final end product must be labeled in visible area with the following: L’équipement final doit être étiqueté sur un endroit visible avec le texte suivant : “Contains IC: 11664A-SORADIO”...
Need help?
Do you have a question about the SORADIO and is the answer not in the manual?
Questions and answers