Table Of Contents - ABB TZIDC Manual

2 TZIDC, TZIDC-200 DIGITAL POSITIONER | COI/TZIDC/TZIDC-200-EN REV. B

Table of contents

1 Safety .......................................................................... 4
General information and instructions .................................. 4
Warnings .................................................................................... 4
Intended use ............................................................................. 4
Improper use ............................................................................. 4
Cable glands .............................................................................. 4
Warranty provisions ................................................................. 4
Cyber security disclaimer ....................................................... 5
Software downloads ............................................................... 5
Manufacturer's address .......................................................... 5
Service address......................................................................... 5
2 Operation ................................................................... 6
Safety instructions ................................................................... 6
Parameterization of the device ............................................. 6
Menu navigation .................................................................. 6
Menu levels ................................................................................ 7
Operating modes ..................................................................... 7
Operating mode 1.0: Control with adaptation .............. 7
Operating mode 1.1: Control without adaptation ......... 7
Operating mode 1.2: Manual adjustment in the stroke
range ...................................................................................... 8
Operating mode 1.3: Manual adjustment in the sensor
range ...................................................................................... 8
Locks........................................................................................... 9
3 Configuration ........................................................... 10
General information ............................................................... 10
Example .................................................................................... 10
Parameter description HART® ............................................. 11
HART parameter overview (graphic) .................................. 14
Parametergroup 1: Standard ................................................ 15
ACTUATOR - actuator type ............................................. 15
AUTO_ADJ - Automatic adjustment .............................. 15
ADJ_MODE - Automatic adjustment mode .................. 16
TEST - Test ......................................................................... 16
FIND_DEV - find device .................................................... 17
EXIT - Back to work level .................................................. 17
Parameter group 2: Set point............................................... 17
MIN_RGE - min. set point range ..................................... 17
MAX_RGE - max. set point range ................................... 17
CHARACT - characteristic curve ..................................... 18
ACTION - direction of action (setpoint signal) ............ 18
SHUT_CLS - Shut-off value 0 % ...................................... 18
SHUT-OPN - Shut-off value 100 % ................................. 18
RAMP UP - set point ramp (up) ....................................... 19
RAMP DN - Set point ramp (down) ................................ 19
EXIT - Back to work level .................................................. 19
Parameter group 3: Working range ..................................... 20
MIN_RGE - min. operating range .................................... 20
MAX_RGE - max. operating range .................................. 20
ZERO_POS - zero point position .................................... 21
EXIT - Back to work level .................................................. 21
Parameter group 4: Messages ............................................ 22
TIME_OUT - stroke time monitoring ............................. 22
POS_SW1 - switching point SW1 .................................... 22
POS_SW2 - switching point SW2 ................................... 22
SW1_ACTV - Active Direction SW1 ................................. 23
SW2_ACTV - Active Direction SW2 ................................. 23
EXIT - Back to work level ................................................. 23
Parameter group 5: Alarms .................................................. 24
LEAKAGE - Leakage to actuator .................................... 24
SP_RGE - set point monitoring ...................................... 24
SENS_RGE - operating range up-scaled ....................... 24
CTRLER - controller inactive ........................................... 24
TIME_OUT - stroke time monitoring ............................. 25
STRK_CTR - Movement counter ..................................... 25
TRAVEL - travel counter ................................................... 25
EXIT - Back to work level ................................................. 25
Parameter group 6: Manual adjustment ........................... 26
MIN_VR - min. working range .......................................... 26
MAX_VR - max. operating range .................................... 26
ACTUATOR - actuator type ............................................. 27
SPRNG_Y2 - spring action (Y2) ....................................... 27
DANG_DN - Dead Angle Close ........................................ 27
DANG_UP - Dead Angle Open ......................................... 27
BOLT_POS - actuator bolt position ............................... 27
EXIT - Back to work level ................................................. 28
Parameter group 7: Controller parameters....................... 28
KP UP - KP value (up) ........................................................ 28
KP DN - KP value (down) .................................................. 29
TV UP - TV value (up) ........................................................ 29
TV DN - TV value (down) .................................................. 29
Y-OFS UP - Y offset (up) .................................................. 30
Y-OFS DN - Offset (down) ............................................... 30
TOL_BAND - Tolerance band ........................................... 31
DEADBAND - Dead band................................................... 31
DB_APPR - Deadband Approach ..................................... 31
DB_CALC - Deadband Determination ............................ 31
LEAK_SEN - Leak Sensitivity ........................................... 32
EXIT - Back to work level ................................................. 32
Parameter group 8: Analog output .................................... 32
MIN_RGE - Current range min. ....................................... 32
MAX_RGE - Current range max. ..................................... 32
ACTION - Direction of action of the characteristic
curve .................................................................................... 32
ALARM - Alarm ................................................................... 33
RB_CHAR - Calculate back to characteristic ................ 33
TEST - Test ......................................................................... 33
ALR_ENAB - Alarm through the analog output ........... 33
CLIPPING - Extending the signal output range ........... 33
EXIT - Back to work level ................................................. 34