Related Manuals for Lissmac CDR 200
Summary of Contents for Lissmac CDR 200
- Page 1 OPERATING MANUAL CORE DRILL STAND CDR 200 CDR 250 CDR 351 LISSMAC Maschinenbau GmbH Lanzstrasse 4 D-88410 Bad Wurzach Telephone +49 (0) 7564 / 307- 0 Fax +49 (0) 7564 / 307 - 500 lissmac@lissmac.com www.lissmac.com 1/34...
- Page 2 2/34...
- Page 3 Imprint The operating manual is valid for: LISSMAC- Core drill stand: CDR 200 CDR 250 CDR 351 Company headquarters: LISSMAC Maschinenbau GmbH Lanzstraße 4 D - 88410 Bad Wurzach Phone: +49 (0) 7564 / 307 – 0 Fax: +49 (0) 7564 / 307 –...
-
Page 4: Table Of Contents
Cleaning ........................21 10.1. Adjusting the carriage guides ..................22 Troubleshooting ......................23 Tools RPM ........................24 Warranty ........................25 Spare parts list CDR 200....................26 Spare Parts list CDR 250 ....................28 Spare parts list CDR 351....................30 4/34... -
Page 5: Table Of Contents Properties & Advantages
Precise adjustment of the drill stand via four levelling screws. Sliders and rollers made of damping PU material with maintenance-free grooved bearings. Ergonomic carrying handle - for simple handling on the construction site. CDR 200 CDR 250 CDR 351... -
Page 6: Operating Manual
Required core drill motor In order to operate the core drill rig, a LISSMAC core drill motor must be inserted into the core drill rig. Motors from other manufacturers must correspond as far as possible to the recommended LISSMAC motors in terms of dimensions, weight and power. -
Page 7: Safety Notices
The warning notices in this manual are not universally complete. Lissmac cannot foresee every potential hazard. Use common sense when dealing with machinery and equipment. Appropriate safety rules and precautions with respect to working methods and operation must be implemented, as with any other machine. - Page 8 Warning and safety notices: Read the operating manual Wear hearing protection Wear safety goggles Wear gloves Wear a protective helmet Wear work boots Wear suitable work clothes and wash dusty clothes Remove the power plug before working on the machine Wear dust protection mask (for dry drilling) Wait for all parts to stop moving.
-
Page 9: Intended Use
Intended use The LISSMAC Core Drill stand is used as a guiding and fastening aid for a LISSMAC Core Drill Motor. A LISSMAC Core Drill Motor with a diamond core bit approved for it must be used for drilling. The operating manual of the core drill motor must be observed! The core drill stand is exclusively intended for commercial use. -
Page 10: Personnel Choice And Personnel Qualification; Basic Responsibilities
3.3. Personnel choice and personnel qualification; basic responsibilities Only qualified personnel 18 years of age or older may operate the machine independently. All personnel must be trained in the operation and be explicitly authorized by the company to operate the machine. Make sure that only authorized personnel works at the machine. -
Page 11: Commissioning
3.4.2. Commissioning Read the operating instructions before commissioning. Wear personal protective equipment. Ensure that the foundation where the drilling is done meets the load carrying capacity. All obstacles must be cleared away from the drilling area and make sure there is sufficient lighting. It must be ensured that no power or telecommunication lines, gas or water pipes, are located in the drilling area. -
Page 12: Special Work While Using The Machine
During service and repair work, always tighten loose bolt joints! Lissmac Core drilling motors may not be used for overhead drilling. 3.4.5. Moving the core drill stand Moving the core drill stand may only be used when disconnected from power. -
Page 13: Machine Description
MACHINE DESCRIPTION Pos. 1 Column top cover Pos. 9 Levelling screws Pos. 2 Drill column Pos. 10 Baseplate Pos. 3 Depth and tilt scale Pos. 11 Column support struts Pos. 4 Spirit level Pos. 12 UNIVERSAL-Connector Pos. 5 Carriage Pos. 13 Baseplate handle Pos. -
Page 14: Technical Data
4.1. Technical data CDR 200 CDR 250 CDR 501 Core bit maximum Ø 200 mm 250 mm 350 mm Core bit - maximum Ø 112 mm when using vacuum Adjustable useful length 565 mm 605 mm 700 mm Motor assembly using... -
Page 15: Transport
TRANSPORT Notice Before transport the core drill motor must be removed from the core drill stand. Lock the carriage in place before transport. COMMISSIONING - ASSEMBLY AND SETTINGS 6.1. Securing the core drill stand 6.1.1. Securing using drop-in anchors Warning! Securing using drop-in anchors is only allowed in concrete. -
Page 16: Securing Via Threaded Rod & Lock Nut
6.1.2. Securing via threaded rod & lock nut Warning! If the substrate is unsuitable for drop-in anchors, a threaded rod M12 (Pos. 1) together with a large washer (Pos. 2) and self-locking nut (Pos. 3) at the back of the wall can be used to secure the drill stand. ... -
Page 17: Assembly Of The Core Drill Motor
6.3. Assembly of the core drill motor Warning! The core drill motor must be disconnected from the power source before installation, cleaning and servicing! Support UNIVERSAL-Connector 1. Lock carriage in place at suitable height (Pos. 1) Carriage Mounting plate / 2. -
Page 18: Set Column Tilt
6.4. Set column tilt Notice Lower drill pressure must be selected for drilling at an angle to prevent the core bit from leaving the intended trajectory. For shallow angles, the use of spot drilling aids to center the core bit is recommended. 1. -
Page 19: Operation
For dry drilling the use a face mask and suitable dust extraction unit is mandatory Distance A for recommended drop-in anchor placement: CDR 200 = 280 mm (Center clamping collar) CDR 250 = 250 mm (Connection plate) CDR 251 = 260 mm (Connection plate) -
Page 20: Use Of Accessories
USE OF ACCESSORIES 8.1. Wheelset If necessary, a set of wheels can be mounted to facilitate transport between sites. CDR 200 CDR 250 / CDR 351 (standard) • Place mounting bracket (pos. 1) on the base plate and fasten with enclosed screws (pos. 1+2). -
Page 21: Maintenance
MAINTENANCE Warning! Always unplug and dismount the core drill motor from the stand before maintenance. Before each use Daily Visual inspection for recognisable damage and deficiencies Check bolts for tightness and tighten if necessary. Check guide column for wear and damage ... -
Page 22: Adjusting The Carriage Guides
10.1. Adjusting the carriage guides Over time, the clearance between the guide and the support may develop. To avoid vibration and damage, the clearance must be as small as possible. Guide rollers adjustment CRD 250 CDR 351 Loosen the screws Place the rollers on the guideway by hand, check (Pos. -
Page 23: Troubleshooting
TROUBLESHOOTING Warning! Always unplug the core drilling motor before troubleshooting. Problem Possible cause Remedy Carriage does not run smoothly Stand and guides are dirty Clean, Lubricate Check levelling screws and quick clamping Vibrations during Operation Stand is loose spindle to be tightened. Play in carriage guides Readjust rollers or glide pads. -
Page 24: Tools Rpm
TOOLS RPM Peripheral speed m/s Diamond core bit diameter mm Specification for concrete Depending on the application purpose and area, tools are different. To have the best results, the parameters must match. With this diagram, the optimal cutting performance can be determined. 24/34... -
Page 25: Warranty
WARRANTY The warranty for this machine is 12 months. For the following listed wear parts the warranty only applies if the wear is not caused by operation. Wear parts are parts that with intended use of the machine have limited operational wear. The wear time is not uniformly specified, it differs according to intensity of use. -
Page 26: Spare Parts List Cdr 200
SPARE PARTS LIST CDR 200 Item. Item No. Part Column cover Column Screw Slider Grip Screw Support bar Bushing Screw Baseplate Set screw Nu8t Washer Adapter Screw Locking screw Scale depth cm Scale degree CDR 200 A Stand: 03/2021 26/34... - Page 27 Item No. Part Screw Lever Slider A Slider B Set screw A Gear spindle Bearing Circlip Locking screw Set screw B Carriage block Screw Fixer Screw Motor clamp Drill press handle 1-15 Carriage complete CDR 200 B Stand: 03/2021 27/34...
-
Page 28: Spare Parts List Cdr 250
SPARE PARTS LIST CDR 250 Item. Item No. Part Column cover Column Screw Slider Grip Screw Support bar Bushing Screw Grip Screw Set screw Washer Adapter Screw Base plate Washer Locking screw Column attachment Scale depth cm Scale degree 10-17 Base plate complete CDR 250 A Stand: 03/2021... - Page 29 Item. Item No. Part Column cover Column Screw Slider Grip Screw Support bar Bushing Screw Grip Screw Set screw Washer Adapter Screw Base plate Washer Locking screw Drill press handle 1-17 Base plate complete CDR 250 B Stand: 03/2021 29/34...
-
Page 30: Spare Parts List Cdr 351
SPARE PARTS LIST CDR 351 Item. Item No. Part Socket hex screw M8x12 Column Cover Column Steel rack Socket hex screw M5x12 Scale depth Scale angle Slider Grip Round head screw M10x30 Bushing Socket hex screw Support bar Column holder Socket hex screw M6x14 Socket hex screw M8x16 Hex screw M12x80... - Page 31 CDR 351 A Stand: 03/2021 31/34...
- Page 32 Item. Item No. Part Circlip 20 Bearing 6804-RS Gear spindle Level Carriage Bearing bushing 12mm Roller Roller pin Roller pin bias Socket hex screw M6x35 Brake Brake screw Brake base Socket hex screw M8x12 Round locator Socket hex screw M6x20 Motor plate Drill press handle 27-43...
- Page 33 Person entitled to compile technical documentation: Head of Design / Technical Documentation Description of the The LISSMAC core drill stand serves as a support and guide for a core drill motor. For drilling, a core drill machine motor approved for this purpose must be used with a diamond drill bit as the tool.
- Page 34 34/34...