Table of Contents
Advertisement
Quick Links
Installation and Operation Manual
When diaphragms fail in AODD pumps, dangerous process fluids are expelled from the pump's air exhaust
putting employees, equipment and the environment at risk. The fully pneumatic SPILLSTOP™ system prevents
the hazardous spill by safely capturing expelled fluid and automatically shutting down the failed pump. Optional
warning alarm and backup pump switchover further minimize system downtime for maximum productivity.
Visit
www.Blacoh.com
for literature online.
Advertisement
Table of Contents
Related Manuals for Blacoh Spillstop
Summary of Contents for Blacoh Spillstop
- Page 1 When diaphragms fail in AODD pumps, dangerous process fluids are expelled from the pump’s air exhaust putting employees, equipment and the environment at risk. The fully pneumatic SPILLSTOP™ system prevents the hazardous spill by safely capturing expelled fluid and automatically shutting down the failed pump. Optional warning alarm and backup pump switchover further minimize system downtime for maximum productivity.
-
Page 2: Table Of Contents
Information in this document is subject to change without notice. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic or mechanical, including photocopying and recording for any purpose other than the purchaser’s personal use without the express written permission of BLACOH Fluid Controls, Inc. BLACOH Fluid Control... -
Page 3: Safety Warnings
Temperature limit is determined by the liquid inside the SPILLSTOP and materials of construction. SPILLSTOP has no moving parts to generate heat. DO NOT use SPILLSTOP with incompatible fluids. Consult distributor or factory if you are not sure of the compatibility of fluids with SPILLSTOP. -
Page 4: Installation & Operation Instructions
Regulator. The quick connect can be removed for hard plumbing. 6. Adjust the Regulator to a minimum of 40 psi (2.7 bar) to start the pump. If the SPILLSTOP is installed with a Whistle and/or more than two Shutoff Valves, increase pressure to a minimum of 60 psi (4.1 bar). -
Page 5: Service
2. Test the Whistle before putting the SPILLSTOP into operation: a. Connect an air line to the Regulator and adjust the Regulator to a minimum of 40 psi (2.7 bar). If the SPILLSTOP is installed with more than two Shutoff Valves, increase pressure to a minimum of 60 psi (4.1 bar). -
Page 6: Troubleshooting
8. Disconnect all air supply to the pump and SPILLSTOP and reinstall the Pump Shutoff Valve. Verify that compressed air is supplied to Port A and that the pump’s air inlet is connected to Port B. Reapply compressed air to the SPILLSTOP to start the pump. If the pump does not operate normally, the valve may be undersized for the application. -
Page 7: Typical Installation Diagram
Figure 1 Typical Installation Diagram BLACOH Fluid Control... -
Page 8: Pump Shutoff Valve
Figure A 1 Pump Shutoff Valve BLACOH Fluid Control... -
Page 9: Pump Shutoff Valve, 1 Exhaust Shutoff Valve
Figure B 1 Pump Shutoff Valve, 1 Exhaust Shutoff Valve BLACOH Fluid Control... -
Page 10: Pump Shutoff Valves
Figure C 3 Pump Shutoff Valves BLACOH Fluid Control... -
Page 11: Pump Shutoff Valves, 1 Exhaust Shutoff Valve
Figure D 3 Pump Shutoff Valves, 1 Exhaust Shutoff Valve BLACOH Fluid Control... -
Page 12: Manufacturer's Limited Warranty & Return Policy
Manufacturer’s Limited Warranty & Return Policy Details regarding warranty and return policy are available on Blacoh’s website at www.Blacoh.com. PROUDLY MANUFACTURED IN THE USA Blacoh Headquarters 601 Columbia Ave, Bldg D, Riverside CA 92507 USA 951.342.3100 | www.Blacoh.com | Sales@Blacoh.com...
Need help?
Do you have a question about the Spillstop and is the answer not in the manual?
Questions and answers