Advertisement
SERVICE MANUAL
SPECIFICATION
Power source
Overall dimension(Net dimension)
Net weight
Power consumption
Motor output
Marked capacity of washing/spinning
Washing method
Water capacity
Water consumption
Pulsator speed
Spinner tub speed
Specification: Subject to change without notice.
Automatic Washer
AC 220V, 60Hz
500(W) × 535(D) × 895(H)
27kg
300W
150W
6.8kg
Automatic reverse turn
45 Liters
106 Liters (Regular wash cycle
Water level: High)
170 rpm(DELICATE 60 rpm)
850 rpm
LSP680GR
(Philippines)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Whirlpool LSP680GR
Summary of Contents for Whirlpool LSP680GR
- Page 1 SERVICE MANUAL Automatic Washer LSP680GR (Philippines) SPECIFICATION Power source AC 220V, 60Hz Overall dimension(Net dimension) 500(W) × 535(D) × 895(H) Net weight 27kg Power consumption 300W Motor output 150W Marked capacity of washing/spinning 6.8kg Washing method Automatic reverse turn Water capacity...
-
Page 2: Abnormal Condition
ABNORMAL CONDITION When the washer is abnormal, the washer stops as the every actions turns off, beep tone sounds ON-0.1 second and OFF-0.1 second for 6 seconds and number window LED display abnormal code. The washer judges the following six conditions as abnormal condition. 1) Abnormal condition of water supply In supplying with water, the water level does not reach extra low level within 10 minutes or does not reach your chosen water level within 20 minutes. -
Page 3: Circuit Diagram
CIRCUIT DIAGRAM COLOR SYMBOL GRAY BLUE GREEN BLACK LIGHT BLUE BROWN ORANGE PINK WHITE YELLOW VIOLET THOUBLESHOOTING TROUBLE INSPECTION INSPECTION CAUSES REMEDY a. Power Source Any indications Is fuse blown? Deterioration of fuse. Replace. and beep do not Motor is defective. Replace. -
Page 4: Water Supply
TROUBLE INSPECTION INSPECTION CAUSES REMEDY b. Water Supply Water does not Does humming Something on the filter of flow when the noise come on the water valve or hose Clean the filter. power switch is from water joint assembly. start valve？... - Page 5 TROUBLE INSPECTION INSPECTION CAUSES REMEDY c. Wash/Rinse ’ Bearing ass y is defective. Replace. Washing cycle does Does the spin tub Poor connect of 6-pin not start even if rotated normally Replace. connectors (blue & white) water keeps the when the Thermostat on motor is selected water level.
-
Page 6: Spin Drying
TROUBLE INSPECTION INSPECTION INSPECTION CAUSES REMEDY Repair or replace. ’ Drain takes time too Drain hose ass y is deformed. long. Hose is connected in the Repair. wrong way. Note: In draining, the water lever sensor can Note: In draining, the water level sensor can Hose is too long or position of Repair. - Page 7 TROUBLE INSPECTION INSPECTION INSPECTION CAUSES REMEDY Operation of safety device Start of spin-drying. Safety device work. Normal spin. Electric circuit works to stop Electric circuit spin when safety device counts operation detects continuously three of safety device. times of abnormal swing of spin drum.
- Page 8 TROUBLE INSPECTION INSPECTION CAUSES REMEDY Buzzing/rattling Does some noise Belt is slipping. Adjust. during washing sound during Pulley is loose. Tighten. or rinsing. spin drying? Some part touch motor Repair or replace Something underneath Remove. pulsator. ’ Pulsator is rubbing. Adjust bearing ass ’...
-
Page 9: Part List
PART LIST ’ Key No. Part No. Description 中文名称 301B801701454 Control Circuit Board Complete 电脑板完成 ST1TN40160SE SCR 4×16 4X16 螺钉(电脑板安装用) 301B121000528 Panel sticker 控制板塑贴印刷完成 301B141400166 Lid Handle 上盖把手喷漆印刷完成 ST1TN40100SE SCR 4×10 4X10 螺钉(把手固定用) 3012160510146 Screw Lid 螺钉盖 3014201S02140 magnet 磁性开关用永磁铁 3012161404040 Washer Lid 洗涤上盖... - Page 10 ’ Key No. Part No. Description 中文名称 3012912223140 SCR 4×8 4X8 螺钉( 后罩盖安装 用) 3012122232140 Back Cover 后罩盖 3012122101142 Frame Handle 箱体把手 3012122302140 Drain Cap 排水口盖 3012334001140 Hose Band 软管卡簧(排水内管和外桶) 3010324703140 Drain Hose (Inside) 排水内管组件 3012912203140 Special screws M5×14 特种螺钉 M5×14 ST1TN40140SE SCR 4×14E 螺钉...
- Page 11 ’ Key No. Part No. Description 中文名称 3010212306143 Lint filter Assembly 滤网组件 3012324518141 Circulate Hose 循环水道 ST1TN40100UK- SCR 4×10K 4×10 螺钉(紧固循环水道用) 3010234425140 Suspension Rod Complete 吊杆完成 Suspension Rod Complete (Motor 吊杆完成(电机侧) 3010234426140 Side) 3012221104040 Outer Tub Drum 外桶体 3012212202140 Drain Pipe 底栓...
-
Page 12: Exploded View
ExplodedView...
Need help?
Do you have a question about the LSP680GR and is the answer not in the manual?
Questions and answers
how to drain the water from the washing machine lp680gr
To drain water from a Whirlpool LSP680GR washing machine:
1. Ensure the drain hose is properly positioned. It should not be too long (maximum 3 meters) or too high (maximum 10 centimeters).
2. Start the drain function by selecting the appropriate wash cycle.
3. If the water does not drain, check for blockages in the drain hose.
4. If draining still fails, the machine may display an abnormal condition code, and the buzzer will sound.
5. If issues persist, inspect the drain system components or seek professional repair.
This answer is automatically generated
only the agitator is spinning when in spin mode
The agitator spinning but not the drum in spin mode on a Whirlpool LSP680GR could be due to a defective bearing assembly, faulty motor torque, a malfunctioning brake lever, or an issue with the motor pulley assembly. Additionally, poor contact in the 6-pin connectors or a defective control circuit board may also cause this issue. Inspect and replace the faulty components as needed.
This answer is automatically generated