Subscribe to Our Youtube Channel
Related Manuals for Truper HILA-2000
Summary of Contents for Truper HILA-2000
- Page 1 Manual Electric Pressure Washer 13.8 MPa 2 000 PSI Applies for: Code Model 101595 HILA-2000 HILA-2000 Read this manual thoroughly CAUTION before using the tool.
-
Page 2: Table Of Contents
Contents CAUTION Technical data Power requirements To gain the best performance of the tool, prolong the duty life, General power tool safety warnings make the Warranty valid if necessary, and to avoid hazards Safety warnings for power washers of fatal injuries please read and understand this Manual before Parts using the tool. -
Page 3: Technical Data
Technical data HILA-2000 Code 101595 Description Pressure washer Maximum pressure 2 000 PSI Maximum inlet pressure 50 PSI Maximum inlet temperature Maximum water flow 113 °F 1.8 gal/min Minimum inlet pressure 35 PSI Voltage Frequency Current 127 V 60 Hz... -
Page 4: General Power Tool Safety Warnings
General power tool safety warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references. -
Page 5: Safety Warnings For Power Washers
Safety Warnings for Power Washers Before operating the pressure washer WARNING • Wear eye protection and heavy clothing. • Always use both hands when spraying in order to have full control CAUTION • Consider that pressure spray is very powerful of the high-pressure gun. -
Page 6: Parts
Parts Carrying handle High pressure High pressure hose support support Accessory holder Switch Power cable holder Power cord Detergent dosing nozzle Detergent tank Water connection Transport wheels High pressure outlet Nozzle cleaner Filters Quick connector Locking button Lance with Lance with turbo nozzle pressure regulating... -
Page 7: Assembly
Assembly • Remove the packing plugs from the water inlet and outlet of the unit. • Assemble the external filters (A) and (B) as shown in the picture and place it in the water inlet of the pressure washer (C). Use the black part of the filter (A) to assemble it to the machine. -
Page 8: Start Up
Start Up Turning ON 1. Turn on the water faucet and keep it on while using the pressure washer. Maximum inlet pressure: 50 PSI. 2. Connect the plug to the outlet. 3. Squeeze and hold the high-pressure gun trigger to release air trapped in the pressure washer. Release the trigger when the water flow is constant. -
Page 9: Maintenance
1 and 2. • Carbon brushes should be checked periodically and always be replaced by a Truper Authorized Service Center Lubrication of the pressure washer when they have worn out. After they have been replaced, request the new carbons to be inspected and confirm that •... -
Page 10: Troubleshooting
Troubleshooting Problem Possible cause Solution The pressure washer • The pressure washer is not connected. • Connect the pressure washer. will not start. • Defective power outlet. • Use a different power outlet. • Blown fuse. • Replace the fuse. Turn other machines OFF. •... -
Page 11: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. -
Page 12: Warranty Policy
. Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.
Need help?
Do you have a question about the HILA-2000 and is the answer not in the manual?
Questions and answers