Makita RBC2500 Instruction Manual

Brush cutter and string trimmer

Hide thumbs Also See for RBC2500:

Original instruction manual (56 pages)

Owner's and safety manual (60 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Makita RBC2500

Page 1 RBC2500 ISTRUZIONI D’USO MANUAL DE INSTRUCCIONES Important: Read this instruction manual carefully before putting the Brush Cutter/String Trimmer into operation and strictly observe the safety regulations! Preserve instruction manual carefully! Importante: Prima di mettere in funzione il decespugliatore/tagliabordi, leggere attentamente il presente manuale; rispettare rigorosamente le norme di sicurezza! Conservare il manuale delle istruzioni per l’uso!
Page 2: Table Of Contents
Thank you very much for purchasing the MAKITA Brush Cutter/String trimmer. We are pleased to recommend to you the MAKITA Brush Cutter/String trimmer which is the result of a long development programme and many years of knowledge and experience. Please read this booklet which refers in detail to the various points that will demonstrate its outstanding performance.
Page 3: Safety Instructions
– It is recommended only to lend the Brush Cutter/String trimmer to people who have proven to be experienced with Brush Cutter/String trimmers. Always hand over the instruction manual.
Page 4 (risk of gas poisoning). Carbon monoxide is an odorless gas. – Switch off the engine when resting and when leaving the Brush Cutter/ String trimmer unattended, and place it in a safe location to prevent danger to others or damage to the machine.
Page 5 Cutting Tools Employ only the correct cutting tool for the job in hand. RBC2500 with cutter blade (Star Blade (4 teeth), Eddy Blade (8 teeth)), RBC2510 with Nylon cutting head. For cutting thick materials, such as weed, high grass, bushes, shrubs, underwood, thicket etc.
Page 6 (waste paper recycling). The undersigned, Yasuhiko Kanzaki, as authorized by MAKITA INTERNATIONAL EUROPE LTD., Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, U.K., declare that the Makita Machines, Type : RBC2500, RBC2510...
Page 7: Technical Data
Sound pressure level average to ISO 7917 Sound power level average to ISO 10884 Fuel Gear ratio kg/h g/kwh type type type Mixed gas(gasoline: Makita Genuine Two-stroke Engine Oil =50:1) RBC2500 RBC2510 U handle Loop handle 1770x620x410 1770x340x220 24.5 0.73 at 7000 min...
Page 8: Designation Of Parts
DESIGNATION OF PARTS RBC2500 U Handle Type RBC2510 Loop Handle Type DESIGNATION OF PARTS Fuel Tank Rewind Starter Air Cleaner I-O Switch (on/off) Spark Plug Exhaust Muffler Clutch Case Rear Grip Hanger Handle Control Lever Control Cable Shaft Protector Gear Case...
Page 9: Assembly Of Engine And Shaft
ASSEMBLY OF ENGINE AND SHAFT CAUTION: Before doing any work on the brush cutter, always switch off the motor and pull the spark plug connector off the spark plug. Always wear protective gloves. CAUTION: Start the brush cutter only after having assembled it completely. –...
Page 10: Mounting Of Handle
MOUNTING OF HANDLE CAUTION: Before doing any work on the brush cutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the brush cutter only after having assembled it completely. For machines with U Handle models –Place the handle-fixing metal so that the handle with the control lever will be positioned on the right (the right-hand grip side) as viewed from the engine...
Page 11: Mounting Of Protector
To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine MAKITA cutter blades or nylon cutting head. – The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately.
Page 12: Mounting Of Cutter Blade Or Nylon Cutting Head
MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD Turn the machine upside down, and you can replace the cutter blade or the nylon cutting head easily. – Insert the hex wrench through the hole in the gear case and rotate the receiver washer (3) until it is locked with the hex wrench.
Page 13: Fuels/Refuelling
FUELS/REFUELLING Handling fuel Utmost care is required when handling fuel. Fuel may contain substances similar to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel vapors, avoid any contact of fuel or oil with your skin. Mineral oil products degrease your skin.
Page 14: Correct Handling Of Machine
CORRECT HANDLING OF MACHINE Attachment of shoulder strap – Adjust the strap length so that the cutter blade will be kept parallel with the ground. Detachment – In an emergency, push the notches (1) at both sides, and you can detach the machine from you.
Page 15: Resharpening The Cutting Tool
– Run the engine for approximately one minute at a moderate speed before applying full throttle. Note: – If the starter handle is pulled repeatedly when the choke button remains at “ excessive fuel intake. – In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also,dry the electrode section of the spark plug.
Page 16 NYLON CUTTING HEAD The nylon cutting head is a dual string trimmer head capable of both automatic and bump & feed mechanisms. The nylon cutting head will automatically feed out the proper length of nylon cord by the changes in centrifugal force caused by increasing or decreasing rpms.
Page 17: Servicing Instructions
– Align the protrusion on the underside of the cover with the slots of the eyelets. Then push cover firmly onto the housing to secure it. SERVICING INSTRUCTIONS SERVICING INSTRUCTIONS CAUTION : Before doing any work on the Brush cutter, always switch off the motor and pull the plug cap off the spark plug (see “checking the spark plug”).
Page 18 Supply of grease to gear case – Supply grease (Shell Alvania 3 or equivalent) to the gear case through the grease hole every 30 hours. (Genuine MAKITA grease may be purchased from your MAKITA dealer.) Suction head in the fuel tank –...
Page 19: Storage
STORAGE – When the machine is in storage for a long time, drain fuel from the fuel tank and carburetor, as follows: Drain all fuel from the fuel tank. Dispose of properly and in accordance with all local laws. – Remove the spark plug and a few drops of oil into the spark plug hole. Then, pull the starter gently, so that oil covers the engine inside and tighten the spark plug.

This manual is also suitable for:

Rbc2510 Rbc2500g Rbc2510g Rbc3100 Rbc3110 Rbc3101

Makita RBC2500 Instruction Manual

Quick Links

Related Manuals for Makita RBC2500

Summary of Contents for Makita RBC2500

This manual is also suitable for:

Table of Contents