Advertisement
Quick Links
Advertisement
Related Manuals for TSS Belt Squat Machine
Summary of Contents for TSS Belt Squat Machine
- Page 1 Belt Squat Machine...
-
Page 2: Personal Safety
Read safety warnings, instructions illustrations provided for this piece of strength equipment. Failure to follow all instructions listed below may result in serious injury or death. User assumes all potential risks of assembly or use of this product. PERSONAL SAFETY ●... - Page 3 ● Crescent Wrench ● 9/16” Socket and Wrench ● 5/32 Allen Key Parts BSM-003 (x2) Part C BSM-001 (x1) Part A BSM-004 (x2) Part D BSM-002 (x1) Part B BSM-005 (x1) Part E...
- Page 4 BSM-006 (x1) Part F BSM-010 (x1) Part J BSM-007 (x1) Part G BSM-011 (x2) Part K BSM-008 (x1) Part H BSM-012 (x1) Part L BSM-013 (x1) Part M BSM-009 (x2) Part I...
- Page 5 4.5” Pulley (x2) Part T *Pre-assembled* BSM-014 (x1) Part N 2.5” Pulley (x2) Part U *Pre-assembled* ⅜ x 3” Bolt (x20) Part O ⅝” x 2.5” Bolt (x6) Part V ⅜” Lock Nut (x24) Part P ⅝” Flat Washer (x6) Part W ⅜”...
- Page 6 Assembly Part C will be placed into part B as seen in image 1.
- Page 7 Parts O, P, and Q are placed in the orientation as seen in image 2 connecting part B and C. The hardware must be hand tight until further components are assembled.
- Page 8 Part D will be placed into part B as seen in image 3.
- Page 9 Parts O, P, and Q will be placed in the orientation seen above in image 4 to connect parts D and B.
- Page 10 Part E and the corresponding hardware (parts, P, O, and Q) are attached as seen above in image 5.
- Page 11 Parts K and J are attached with parts W and V as seen above in image 6.
- Page 12 Image 7 above displays the complete assembly of the base for the belt squat machine. Once all components are assembled as seen in image 7, all hardware (parts P, O, Q, V, and W) can be tightened with a crescent wrench, 9/16”...
- Page 13 Attach part H to part A as seen above in image 8 and tighten all hardware with a crescent wrench and 9/16” socket.
- Page 14 Attach part A to E as seen in image 9 above. Tighten the hardware components (P, O, and Q) with a crescent wrench and 9/16” socket.
- Page 15 Parts R, I, and G are assembled as seen in image 10 above.
- Page 16 Place the assembled components into part A as seen above in image 11. This is done by placing part I through the top of part A and then lowering part I into the inserts at the bottom of part A.
- Page 17 Place part F into part A in the high or low position (User’s Preference) as seen in image 12.
- Page 18 Part N is placed through parts A and B as seen in images 13 and 14. Parts S and P must be removed in order to feed part N through both components. Once part N has been placed, tighten parts S and P in their respective locations as seen in image 14.
- Page 19 Attach part M as seen above in image 15.
- Page 20 Part K is placed through part A as seen above in image 16 and is secured with part R by using a 5/32 allen key.
- Page 21 *Part WS can be placed in the locations marked above in image 17 (Upgrade).* Part WS will be attached to all locations in image 17 as seen in image 18 with components O, P, and Q.
- Page 22 You have now completed assembling your very own Belt Squat Machine! Thank you for choosing Texas Strength Systems for your fitness needs. If you have any questions, comments, or concerns please don’t hesitate to contact our staff. Contact Information Email: wesz@texasstrengthsystems.com Phone: (210) 233-6110, (210)-920-4877...
Need help?
Do you have a question about the Belt Squat Machine and is the answer not in the manual?
Questions and answers