Table of Contents
Advertisement
Quick Links
LCD Projector
MAX-WU55S/MAX-WU55SH
MAX-WU55SE/MAX-WU55SF
User's Manual
Operating Guide – Technical
Supported signals for COMPUTER IN
Resolution (H x V)
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 768
1280 x 800
1280 x 1024
1366 x 768
1440 x 900
1600 x 900
1680 x 1050
1600 x 1200
1920 x 1080
Signal mode
TEXT
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 16" mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
1152 x 864 (75Hz)
W-XGA (60Hz)
1280 x 800 (60Hz)
SXGA (60Hz)
SXGA (75Hz)
SXGA (85Hz)
WXGA (60Hz)
WXGA+ (60Hz)
WXGA++ (60Hz)
WSXGA+ (60Hz)
UXGA (60Hz)
Full HD (60Hz)
H. frequency
V. frequency
(kHz)
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
48.4
56.5
60
68.7
67.5
47.7
49.7
64
80
91.1
47.7
55.9
60
65.3
75
67.5
1
Rating
(Hz)
85
VESA
59.9
VESA
72.8
VESA
75
VESA
85
VESA
56.3
VESA
60.3
VESA
72.2
VESA
75
VESA
85.1
VESA
74.5
60
VESA
70.1
VESA
75
VESA
85
VESA
75
VESA
60
VESA
60
VESA
60
VESA
75
VESA
85
VESA
59.8
VESA
59.9
VESA
60
VESA
60
VESA
60
VESA
60
VESA
Advertisement
Table of Contents
Related Manuals for PJLink MAX-WU55S
Summary of Contents for PJLink MAX-WU55S
- Page 1 LCD Projector MAX-WU55S/MAX-WU55SH MAX-WU55SE/MAX-WU55SF User's Manual Operating Guide – Technical Supported signals for COMPUTER IN Resolution (H x V) Signal mode H. frequency V. frequency Rating (kHz) (Hz) 720 x 400 TEXT 37.9 VESA 640 x 480 VGA (60Hz) 31.5 59.9...
- Page 2 Supported signals Supported signals for HDMI Resolution (H x V) Signal mode H. frequency V. frequency Rating (kHz) (Hz) 720 x 400 TEXT 37.9 VESA 640 x 480 VGA (60Hz) 31.5 59.9 VESA VGA (72Hz) 37.9 72.8 VESA VGA (75Hz) 37.5 VESA VGA (85Hz)
- Page 3 Supported signals NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC. • Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector. •...
- Page 4 Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 can be output from the COMPUTER IN2/MONITOR OUT port.
- Page 5 Connection to the ports (continued) VIDEO RCA jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz) • 1.0±0.1Vp-p, 75Ω terminator...
- Page 6 Connection to the ports (continued) HDMI1 HDMI2 HDMI3 10 12 14 16 18 • Type :Digital audio/video connector 11 13 15 17 19 • Audio signal : Linear PCM (Sampling rate; 32/44.1/48 kHz) Signal Signal Signal T.M.D.S. Data2 T.M.D.S. Data0 Shield +N.C.
- Page 7 Connection to the ports (continued) USB TYPE A USB TYPE B USB A type jack USB B type jack Signal Signal - Data - Data + Data + Data Ground Ground CONTROL D-sub 9pin plug • About the details of RS-232C communication, 5 4 3 2 1 please refer to the section "RS-232C Communication".
- Page 8 Connection to the ports (continued) To input component video signal to COMPUTER IN ports RCA plugs connectors D-sub plug COMPONENT VIDEO OUT VCR/DVD/Blu-ray Disc player To input component video signal to the COMPUTER IN1 or IN2 port of the projector, use a RCA to D-sub cable or adapter. For about the pin description of the required cable or adapter, refer to the descriptions about COMPUTER IN1 and IN2 port (&4).
- Page 9 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&18). Connection Turn off the projector and the computer.
-
Page 10: Communication Settings
RS-232C Communication (continued) Communication settings 1. Protocol 19200bps , 8N1 (default) (& OPTION menu - SERVICE - COMMUNICATION in the Operating Guide) 2. Command format ("h" shows hexadecimal) Byte Number Command Header Data Header Data Setting Action Type code size flag code Packet... -
Page 11: Response Code / Error Code
RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply : 15h When the projector cannot understand the received command, the projector returns the error code. - Page 12 Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&18).
-
Page 13: Communication Port
Command Control via the Network (continued) Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Port open Control Port1 (Port: 23)] to use TCP #23. -
Page 14: Command Control Settings
Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communication command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4). - Page 15 Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (××h : connection ID) (1) ACK reply : 06h + ××h (2) NAK reply : 15h + ××h (3) Error reply : 1Ch + 0000h + ××h...
- Page 16 Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communication, an external device that is connected with this projector by RS-232C communication can be controlled from the computer as a network terminal. For details, see the 1.5 Network Bridge Function - Network Guide.
- Page 17 Network Bridge Communication (continued) Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. (&OPTION menu - SERVICE - COMMUNICATION in the Operating Guide) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY NONE/ODD/EVEN...
- Page 18 RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting code Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00...
- Page 19 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code STANDARD BE EF 06 00 83 F5 01 00 BA 30 06 00 NATURAL BE EF 06 00 23 F6 01 00 BA 30 00 00 CINEMA BE EF...
- Page 20 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 A1 71 02 00 0D 22 00 00 WIDE DYNAMIC Increment BE EF 06 00 C7 71 04 00 0D 22 00 00 RANGE...
- Page 21 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 7C FF 02 00 97 30 00 00 User Gamma Increment BE EF 06 00 1A FF 04 00 97 30 00 00 Point 8...
- Page 22 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code COLOR TEMP Execute BE EF 06 00 C8 C5 06 00 4C 70 00 00 OFFSET B Reset BE EF 06 00 B5 72 02 00 02 22 00 00...
-
Page 23: Auto Adjust Execute
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 F1 82 02 00 01 21 00 00 H POSITION Increment BE EF 06 00 97 82 04 00 01 21 00 00 Decrement... - Page 24 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUTO BE EF 06 00 0E D8 01 00 24 20 00 00 NORMAL BE EF 06 00 9E D9 01 00 24 20 01 00 HDMI3 RANGE ENHANCED...
- Page 25 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code KEYSTONE BE EF 06 00 6B 8C 01 00 30 31 01 00 GEOMETRIC PERFECT FIT BE EF 06 00 9B 8C 01 00 30 31 02 00 MODE...
-
Page 26: Installation
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code PERFECT BE EF 06 00 31 97 02 00 41 21 00 00 FIT Left Side Increment BE EF 06 00 57 97 04 00 41 21 00 00... - Page 27 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 CD CC 02 00 60 20 00 00 VOLUME - Increment BE EF 06 00 AB CC 04 00 60 20 00 00 COMPUTER IN1...
- Page 28 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 46 D3 01 00 02 20 00 00 MUTE BE EF 06 00 D6 D2 01 00 02 20 01 00 BE EF 06 00...
- Page 29 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 52 DF 01 00 3D 20 00 00 AUDIO IN1 BE EF 06 00 C2 DE 01 00 3D 20 01 00 AUDIO AUDIO IN2...
-
Page 30: Osd Message
RS-232C Communication / Network command table (continued) Command Data Command Data Names Names Operation Type Operation Type Header Header Action Action Type Type Setting code Setting code MyScreen BE EF 06 00 FB CA 01 00 00 30 20 00 ORIGINAL BE EF 06 00... - Page 31 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code TEST PATTERN BE EF 06 00 43 D9 01 00 22 30 00 00 DOT-LINE1 BE EF 06 00 D3 D8 01 00 22 30 01 00 DOT-LINE2...
- Page 32 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code NORMAL BE EF 06 00 FE 78 01 00 20 22 00 00 SEARCH SKIP SKIP BE EF 06 00 6E 79 01 00 20 22 01 00 COMPUTER IN1...
- Page 33 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code COMPUTER IN1 BE EF 06 00 3A 33 01 00 00 36 00 00 COMPUTER IN2 BE EF 06 00 FA 31 01 00 00 36 04 00 BE EF...
-
Page 34: Flicker Reduction
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 C8 D7 02 00 10 30 00 00 Magnify Position Increment BE EF 06 00 AE D7 04 00 10 30 00 00 Decrement... -
Page 35: Usb Type A
PJLink command PJLink command Commands Control Description Parameter or Response 0 = Standby POWR Power Control 1 = Power On 0 = Standby POWR ? Power Status inquiry 1 = Power On 2 = Cool Down 11 = COMPUTER IN 1... - Page 36 INFO ? Other Information inquiry CLSS ? Class Information inquiry 1 NOTE • The password used in PJLink is the same as the password set in the Web Browser Control. To use PJLink without authentication, do not set any password in Web Browser Control.
Need help?
Do you have a question about the MAX-WU55S and is the answer not in the manual?
Questions and answers