Koyo ViewJet GC-A2 Series Quick Start Manual

GC-A2 series
Quick Start Guide
Quick Start Guide
感谢您选用光洋GC-A2系列工业触摸屏，在您使用此产品之前，请先阅读本随机说明。如您
在 使用此产品时有任何的问题，请联系我们！
Thank you for purchasing our GC-A2 series Touch Panel. Please read this Quick Start Guide
carefully before applying the product. If you need any help when you use the product, please consult
us.
KOYO ELECTRONICS (WUXI) CO., LTD.
地址：中国江苏省无锡市滨湖区建筑西路599号1栋21层
Addr：21st Floor, Building 1, No.599, Jianzhuxi Road, Binhu District, Wuxi, Jiangsu, P.R.China
邮编(Pc)： 214072
电话(Tel)：（0510）85167888
传真(Fax)：（0510）85161393
Homepage:http://www.koyoele.com.cn
(Safety Information)
安全情报
・请在电源断开的情况下连接电源线，否则有可能损坏触摸屏或导致人身伤害。
・请不要把触摸屏作为与人的安全或重大伤害有关的开关来使用。 （如紧急安全开关等）
・保护接地端子务必请按第 D 种方法接地，否则有产生电击的可能。
・请在规定的环境范围（温度、湿度、振动、冲击等）内存放、使用触摸屏。
・请不要在有可燃性、爆炸性气体或蒸气的场所使用触摸屏。
・请不要自己分解、改造触摸屏，否则有可能引起故障和其它的问题。
・不要用硬的东西或螺丝刀的尖头等锋利的东西去敲打触摸屏，以免造成触摸屏的损坏或人身的伤害。
・Please connect the power wires when the power is OFF. Otherwise the Touch Panel damage or personal injuny
may be caused.
・Do not use the Touch Panel to make switches that are related to safety of people or major damages
(emergency safety switches, etc).
・Be sure that class D grounding is used for the protective grounding terminal. There is a possibility of electrical
shock if the Touch Panel is not grounded.
・Use and store the Touch Panel in the environment described in the specifications (regarding temperature,
humidity, vibrations, shock, etc).
・Do not use the Touch Panel where it is subjected to flammable or explosive gases, or stream.
・Do not disassemble or modify the Touch Panel. Doing so can cause malfunctions and lead to other problems.
・Do not press on the Touch Panel with screwdrivers or other sharp objects and do not strike it with hard objects.
Doing so can damage the Touch Panel or cause malfunctions.
技术支持 (Technical Support)
如您 在 使用此产品时有任何的问题，请联系我们！ 联系电话：0510-85167888-2075
If you have any question when you use the product, please consult us.
The technical support telephone number is 0510-85167888-2075.
规格认证 (Agency Approval)
本触摸屏已取得 UL、cUL、C E 、RoHS认证 , 请参考产品上的标签。
The Touch Panel conforms to UL,cUL,C E, and RoHS. Please refer to the product label.
1
开箱确认 (Unpack and Inspect)
请确认包装纸箱中有下图所示的物品。
如果有任何的缺少或损坏，请与您的供货商联系。
Please make sure that all insertions shown in the picture are
included in the carton.If any item is missing or damaged,
please contact the store you purchased.
4.3寸以外的型号（Except 4.3"Model）
包装材料
Packing Material
随机手册
Quick Start Guide
GC-A2本体
GC-A2 TouchPanel
安装夹具
Mounting Bracket
其他附件
DC电源接头
海绵衬垫等
Package includes;
DC Power Connection
Gasket
2
通讯口确认 (Communication Ports)
注：图例为10.2"及7.0"屏的外观，与4.3"屏有所不同。
The ports' position of 4.3"Model is different.
USB口 B型( 编程用 )
USB口 A
USB Type B (For Programming)
USB Type A (For USB Device)
Pin Pin Signal Signal
1 1 Vbus Vbus
2 2 1 1
2 2 D– D– 1 1 2 2 3 4 3 4
3 3 4 4
3 3 D+ D+
4 4 GND GND
Shell Shell Shield Shield
※1： GC-A24W-RC/RCW、GC-A26W-RC/RCW 上没有该接口。
※1：Device is not available on
GC-A24W-RC/RCW
KEW-M9513A
4.3寸型号（4.3"Model）
随机手册
Quick Start Guide
安装夹具
Mounting Bracket
DC电源插头
DC Power Connection
GC-A2本体
GC-A2 TouchPanel
包装材料
Packing Material
其他附件
海绵衬垫等
Package includes;
Gasket
点击或双击下载的安装文件，根据提示信息安装GC-A2系列下图软件。
PLC 串行通讯口
Screw Torque:0.3Nm
紧固扭矩
PLC Serial Communication
Pin Pin Signal Signal Pin Pin Signal Signal
1 1 Frame GND Frame GND 6 do not use do not use
8 8 1 1
2 2 TXD (232C) TXD (232C) 7 7 CTS (232C) CTS (232C)
15 15 9 9
3 3 RXD (232C) RXD (232C) 8 8 RTS (232C) RTS (232C)
4 4 do not use do not use 9 9 RXD+ (422/485) RXD+ (422/485)
5 5 Logic GND Logic GND 10 RXD– (422/485) 10 RXD– (422/485)
底部视角
※1
Bottom View
Ethernet 10Base-T/100 Base-TX
以太网口：PLC通讯与编程用
PLC Communications & Programming
Pin Pin Signal Signal Pin Pin
1 1 TD+ TD+ 5 5
( USB 设备用 )
型
2 2 TD– TD– 6 6
3 3 RD+ RD+ 7 7
4 4 do not use do not use 8 8
Pin Pin Signal Signal
1 1 do not use do not use
1 1
Link Status LED (Green) Link Status LED (Green)
2 2 D– D–
On Ehternet Linked On Ehternet Linked
3 3 D+ D+
Off Off No Ethernet Comm. No Ethernet Comm.
4 4 GND GND
and .
GC-A26W-RC/RCW
确
3
PC 与 GC-A2 的连接 (Connect Touch Panel to PC)
如图所示方法来连接触摸屏和 PC。
Connect the Touch Panel to PC as shown.
以太网口
Ethernet Port
PC
Category 5 Straight Cables
4
触摸屏上电 (Provide Power to the Touch Panel)
本触摸屏为DC24V 供电。按下图所示连接 DC24 电源。
Use DC24V for power source.
Connect a DC24V power supply as shown in below figure.
4.3寸以外的型号如下图（Excpet 4.3" Model） 4.3寸型号如下图（4.3" Model）
+
DC20.4~28.8V
-
GND
･电缆要求： AWG12 (3.3mm²)
･接线端子紧固扭矩 : 0.57Nm (5lb-inch)
・ Wire range: AWG12 (3.3mm²)
・ Screw Torque (terminal): 0.57Nm (5lb-inch)
5
如何设定时间 (The time set of a clock)
按"Settings"键
Press "Settings"
6
PLC 与 GC-A2 的连接 (Connect Touch Panel to PLC)
如图所示方法来连接触摸屏和 PLC 。
Connect the Touch Panel to PLC as shown.
2. 以太网交叉电缆连接
（Ethernet Cross Cable Connection)
Pin Pin Signal Signal
11 11
TXD+ (422/485) TXD+ (422/485)
TXD– (422/485) TXD– (422/485)
12 12
H0-ECOM/ECOM100
13 13 Term. Resistor Term. Resistor
14 14 do not use do not use
15 15 do not use do not use
SHELL SHELL Logic GND Logic GND
DL06 PLC
7
作图软件的安装、使用和传送
(Install the Software, Develop and Transfer)
Signal Signal
do not use do not use
RD– RD–
点击或双击下载的安装文件。根据提示信息安装GC-A2系列下图软件。
do not use do not use
启动安装好的GC-A2系列作图软件。
do not use do not use
您就可以开始制作您的用户画面了。
8 8
Network Activity LED (Orange) Network Activity LED (Orange)
Clicking or double-clicking the Installer downloaded.
On On Active Network Data Active Network Data
确
Off Off Network Idle Network Idle Install GC-A2 programming software in accordance to the message of an installer
Then start up GC-A2 programming software.
1. USB 连接
(USB Connection)
3. 以太网HUB连接
(Ethernet HUB Connection)
R
PW
10/
AC T/ 100
LN K rt
10/ link Po
AC T/ 100 Up
LN K
10/
AC T/ 100
LN K U
10/ 0 5
AC T/ 100
K S W
10/ LN
AC T/ 100 E –
K * 包括交换式HUB
LN 以太网口
3
1 2 * Include Switching HUB Ethernet Port
PW R PWR –
+
5类直连线
+
~
DC20.4 28.8V
-
GND
GC-A2状态指示LED (GC-A2 Status LED)
CPU Status LED (Green, Orange & Red) CPU Status LED (Green, Orange & Red)
Off Off
Power off Power off
Green Green
Normal-CPU Run State Normal-CPU Run State
Red Red
System not found
Orange Low Power
按住触摸屏左上角3秒，进入系统设置画面的主菜单画面。
To access the MAIN MENU of the Touch panel setup screens,
press the upper left corner of the panel display area for 3 seconds
as shown to the left.
按"Clock"键
Press "Clock"
3.以太网 HUB
（Ethernet HUB Connection)
以太网口
Ethernet Port H0-ECOM/ECOM100
5类交叉线
Category 5 Cross Cable
DL06 PLC
USB口 B型 ( 编程用 )
PC
USB Type B (For Programming)
USB口 A型
USB Type A
USB 电缆
USB Cable
2. 以太网交叉电缆连接
(Ethernet Cross Cable Connection) 以太网口
Ethernet Port
PC
以太网口 5类交叉线
Ethernet Port Category 5 Cross Cable
･电缆要求： AWG12 (3.3mm²)
･接线端子紧固扭矩 : 0.79Nm (7lb-inch)
・ Wire range: AWG12(3.3mm²)
・ Screw Torque (terminal): 0.79Nm(7lb-inch)
Power LED (Green) Power LED (Green)
On Power On On Power On
PWR PWR
Off Off Power Off Power Off
CPU CPU
TxD TxD
RxD RxD
BATT BATT
Serial TxD/RxD (Green) Serial TxD/RxD (Green)
IOlOl–PLC IOlOl–PLC On On Comm. is active Comm. is active
背面
Off Off No communication No communication
(Rear View)
调整触摸屏内部时钟
Adjust the internal clock
1. 串行口连接 (Serial Connection)
DL06 PLC
Port 2
EA-2CBL-1
连接
PW R
10/
T/ 100
K AC t
10/ link LN Por
AC T/ 100 Up
LN K
10/
AC T/ 100
LN K 0 5 U
T/ 100 10/
AC K S W
10/ LN
T/ 100 E –
AC K 以太网口
LN *
包括交换式HUB
2 3
1 PWR Ethernet Port
PWR + –
* Include Switching HUB
5类直连线
Category 5 Straight Cables
.