Self-Diagnosis Function - Sony DSC-WX50 Service Manual

Ver. 1.2 2012.03
The changed portions from
Ver. 1.1 are shown in blue.
1-5.

SELF-DIAGNOSIS FUNCTION

1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis func-
tion starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
LCD screen
Blinks at 3.2 Hz
C 3 2 0 0
Repaired by: Block
C : Corrected by customer Indicates the appropriate
E : Corrected by service step to be taken.
engineer E.g.
13 ....Format the "memory card".
32 ....Turn on power again.
DSC-WX50_L2
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen shows
a 4-digit display consisting of an alphabet and numbers, which blinks at
3.2 Hz. This 5-character display indicates the "repaired by:", "block" in
which the problem occurred, and "detailed code" of the problem.
Detailed Code
Refer to "1-5-3. Self-diagnosis Code Table".
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Block Detailed
Function Code
The internal memory has experienced a me-
dia error.
The internal memory has experienced a for-
mat error.
Memory card is unformatted.
C 1 3 0 1
Memory card is broken.
Memory card type error
The camera cannot read or write data on the
memory card.
Trouble with hardware
C 3 2 0 1
Abnormality of network control.
E 4 1 0 0 *
Abnormality of network control device.
E 4 1 0 1 *
Difficult to adjust focus
E 6 1 0 0
(Cannot initialize focus)
Zoom operations fault
E 6 1 1 0
(Cannot initialize zoom lens.)
Reset position detection error on the stepper
E 6 1 3 0
iris initializing
E 6 2 0 2 Abnormality of IC for steadyshot.
E 6 2 1 0 Lens initializing failure.
E 6 2 1 1 Lens overheating (PITCH).
Lens overheating (YAW).
E 6 2 1 2
E 6 2 2 0 Abnormality of thermistor.
E 9 1 0 0 Battery / Dry cell distinction defect
E 9 1 0 1 Abnormality when flash is being charged.
Internal memory fault
E 9 4 0 0
E 9 5 0 0 * GPS hardware error
E 9 5 0 1 Acceleration sensor hardware error
Electronic compass hardware error
E 9 5 0 2 *
(GPS hardware error)
Note 1: After repair, be sure to perform "1-6. PROCESS AFTER FIXING FLASH ERROR".
Note 2: Functions of codes with * mark are not provided in this unit.
1-4
– ENGLISH –
Correction
Turn the power off and on again.
Format the internal memory.
Format the memory card.
Insert a new memory card.
Insert a supported memory card.
Turn the power off and on again, or taking out and inserting the memory
card several times.
Turn the power off and on again.
Turn power off and turn power on again.
Turn power off and turn power on again.
Retry turn the power on by the power switch. If it does not recover,
check the focus reset sensor of lens block (pin wk of CN402/CN1402
on the SY-311/SY-321 board). If it is OK, check the focus motor drive
IC (IC401/IC1401 on the SY-311/SY-321 board).
Retry turn the power on by the power switch. Check the zoom reset
sensor of lens block (pin eg of CN402/CN1402 on the SY-311/SY-321
board) when zooming is performed when the zoom button is operated.
If it is OK, check the zoom motor drive IC (IC401/IC1401 on the
SY-311/SY-321 board).
Turn power off and turn power on again.
Check or replacement of the IC for steadyshot (IC401/IC1401 on the
SY-311/SY-321 board).
Check or replacement of the IC for steadyshot (IC401/IC1401 on the
SY-311/SY-321 board).
Check the HALL element (PITCH) of optical image stabilizer (pin
qf, qh of CN402/CN1402 on the SY-311/SY-321 board). If it is OK,
check PITCH angular velocity sensor (SE401/SE1401 on the SY-311/
SY-321 board) peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pin qd,
qa of CN402/CN1402 on the SY-311/SY-321 board). If it is OK, check
YAW angular velocity sensor (SE401/SE1401 on the SY-311/SY-321
board) peripheral circuits.
Check the OIS temp sensor of optical image stabilizer (pin wa of
CN402/CN1402 on the SY-311/SY-321 board).
Checking of flash unit or replacement of flash unit. (Note 1)
Inspect the internal memory (IC211/IC1211 on the SY-311/SY-321
board).
Turn power off and turn power on again.
Turn power off and turn power on again.
Turn power off and turn power on again.