Page 1
EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE POSPrinter (TM-U675) Version 3.00 Feb. 2019...
Page 2
(3) Comments and notification of any mistakes in this documentation are gratefully accepted. (4) This software cannot be used with other equipment that the specified. (5) EPSON will not be responsible for any consequences resulting from the use of any information in this documentation. Trademarks Microsoft®, Windows®, Visual Basic®...
Section 1. Introduction This manual describes the method of use and related items, as well as machine-specific precautions, when the EPSON TM-U675 Series POS Printers are used with the EPSON OPOS ADK program. This manual applies to the following devices.
Version 3.00 Feb. 2019 Section 2. Details on Settings This section describes connection configurations and how to make the settings for the TM-U675 printers. 2.1 References of Firmware Versions Refer to the release notes (Relnote.txt). 2.2 Settings of DIP Switches Confirm that the following settings have been made correctly.
Page 6
Version 3.00 Feb. 2019 Set DIP-SW2-4 (compatible mode with the TM-U375) to match the environment of use. When the switch is set to ON, DIP-SW2-3 is settable; set to OFF fixed. Make other settings in accordance with the settings described above. 2) Parallel Port DIP-SW1 DIP-SW2...
Page 7
Version 3.00 Feb. 2019 3) USB Port DIP-SW1 DIP-SW2 Setting Setting Recommended Recommended Recommended Fixed at OFF Fixed at OFF Recommended Fixed at OFF Settable Fixed at OFF Fixed at OFF Fixed at OFF Fixed at OFF Fixed at OFF Fixed at OFF Fixed at OFF Fixed at ON...
Version 3.00 Feb. 2019 2.3 Port Information 1) Port information when serial port is used The port information that can be set with the SetupPOS utility is as follows. Item Setting range Baud rate [bps] 2400,4800,9600,19200 Bit length [bit] Parity NONE, ODD, EVEN Stop bit [bit] Handshake...
Page 9
Version 3.00 Feb. 2019 2) Port information when using parallel port The port information that can be set with the SetupPOS utility is as follows. Item Setting range Output buffer length [byte] 32 to 1024 Output interval time [ms] 0 to 9999 The default settings are as shown in the following table.
2.4.1 Usable Device Specific Settings For the TM-U675, the following device specific settings are settable by the SetupPOS utility. For the detail, please refer to the Section 2 of “EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE POSPrinter (TM Series)”. Settings...
Version 3.00 Feb. 2019 Section 3. Function Details This section describes the functions of the TM-U675 printers in details. Supplementary explanation of the parts not described in detail in the "UPOS" is also given here. 3.1 Property Set Values and Default Values The following explanation is about the property set values and the default values.
Version 3.00 Feb. 2019 3.1.2 List Properties The List Properties are explained in the following. List Property Settings CharacterSetList “437,850,852,858,860,863,865,866,998, 999,1252” JrnLineCharsList “” RecLineCharsList “37,50” RecLineCharsList “33,40” (Compatible with the TM-U375) SlpLineCharsList “45,60” SlpLineCharsList “33,40” (Compatible with the TM-U375) RecBarCodeRotationList “0, 180”...
Version 3.00 Feb. 2019 3.1.3 Width and Height Properties The width and height properties are described below. Property Settings Default Maximum Minimum Value value [dot] value [dot] RecLineSpacing JrnLineSpacing SlpLineSpacing SlpLineHeight [dot] RecLineHeight [dot] JrnLineHeight [dot] SlpLineWidth [dot] SlpLineWidth [dot] (Compatible with the TM-U375) RecLineWidth [dot] RecLineWidth [dot]...
Version 3.00 Feb. 2019 3.2 Methods The following explanation is about supported/unsupported Methods, and the detailed information. Method Supported/Unsupported Compatibility with the PageMode printing PrintNormal PrintTwoNormal PrintImmediate PrintBarCode PrintBitmap PrintMemoryBitmap CutPaper (1~100: One point remains uncut) MarkFeed ChangePrintSide ValidateData TransactionPrint SetLogo SetBitmap RotatePrint...
Version 3.00 Feb. 2019 3.3 Escape Sequences The following figure is about supported/unsupported Escape Sequences. Escape Sequence Receipt Slip Compatibility with the PageMode printing 0~100 0~100 0~9999 0~9999 0~ approx. 50 cm 0~ approx. 50 cm Maximum [inch] 0~65535 0~65535 !rvC !tbC !tpC...
Version 3.00 Feb. 2019 Numbers: Settable range Supports only for the models with an auto cutter. Regardless of the PageModeHorizontalPosition property setting, center or right adjust what is to be printed based on the PageModePrintArea property setting in the horizontal direction.
To print the registered image file, please use the following DirectIO. PTR_DI_FLASH_BITMAP PTR_DI_FLASH_BITMAP2 For the details of the printing, please refer to the Section 4 of “EPSON OPOS ADK APPLICATION DEVELOPMENT GUIDE POSPrinter (TM Series)”. The available NVRAM size for the TM-U675 is 393216 bytes or 262144 bytes for Multilingual character models.
3.9 Printable Bitmap Types and Sizes The TM-U675 models support the following bitmap commands. For the detail, please refer to the Section 3 of “EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE POSPrinter (TM Series)”. The allowance ranges for bitmaps are as follows.
Begin/EndRemoval, or PrintNormal as normal printing operation. Some properties are automatically changed by the switching. For the detail of the DirectIO methods, please refer to the Section 4 of "EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE POSPrinter (TM Series). Also refer to the Section 5 of the manual for the programming examples.
Version 3.00 Feb. 2019 Section 4. Warnings This section describes precautions in use of TM-U675. There is no specific warning. APPLICATION DEVELOPMENT GUIDE POSPrinter (TM-U675)