Table of Contents
Advertisement
Quick Links
Thank you for choosing our product! Before using your new led lighting system, please carefully read it's instructions
for safe and correct usage!
LRW165-...H
User manual and warranty card
Table of content
ENG
Made in Serbia
2
3
3
3
4
9
10
10
1
Advertisement
Table of Contents
Related Manuals for Lumen LRW165 Series
Summary of Contents for Lumen LRW165 Series
-
Page 1: Table Of Contents
LRW165-...H User manual and warranty card Thank you for choosing our product! Before using your new led lighting system, please carefully read it’s instructions for safe and correct usage! Made in Serbia Table of content Safety instructions and usage of led lighting system Recycling Areas of application Special characteristics of led lighting system... -
Page 2: Safety Instructions And Usage Of Led Lighting System
Safety instructions and usage of led lighting system Please adhere to the following: ● The led lighting system is only installed when it’s not connected to the power source (the cable is not in power connector)! ● The led lighting system does not contain serviceable parts. Do not disassemble the led lighting system by yourself! Repairs of device may only be performed by the manufacturer, otherwise the warranty will not be valid. -
Page 3: Recycling
We do not accept any responsibility for material or personal injuries due to improper handling or non-compliance with safety regulations. Modifications and / or any repairs to the device by the end user or third parties are strictly prohibited for safety reasons and for licensing (CE). If you have any doubts about installation, operation, safety, etc. led lighting system it’self, we kindly ask you to contact us, we will always be happy to help you. -
Page 4: Installation Steps
Installation steps ● Unpack the led lighting system, check that it is not damaged or that all belonging accesories are complete (contact your dealer or manufacturer for any defects) ● Place the two stainless steel legs (7) in the holes on the side of the bracket and tighten them with the hand screws (6) below. - Page 5 ● Remove the protective film from the plexiglass! ● Place the led lighting system with pre-assembled legs on the edges of the aquarium and adjust the legs so that they fit perfectly on both sides of the aquarium. ● In case you opt for the hanging type of mounting of our LED console above your aquarium, the package includes a set of cables for this type of mounting.
- Page 6 2. Mount the cable set on the ceiling Before mounting the cable set on the ceiling / wall, it is necessary to drill holes in the ceiling (1) and install dowels (2) (they are not in the set).When drilling holes in the ceiling / wall, pay attention to the presence of network cables to avoid their direct damage, which can lead to an unwanted case or even an accident! After drilling the holes, it is necessary to place dowels (2) in the holes.Secure the part of the cable set that is mounted on the ceiling (3) with the screws (4) (not included in the set) to the ceiling.
- Page 7 There is no need for an additional timer in addition to the controller, as the controller can control the brightness as well as the time intervals expressed in minutes. Further descriptions and instructions can be found in the control unit manual and the component programs can be accessed or downloaded from the official Lumen-aquatech website (www.lumen-aquatech.com).
- Page 8 ● Connect the power cord to the AC power connector and make sure it is connected properly. ● Plug the timer into a wall outlet and set it to "OFF", then plug the led lighting system plug into the timer. If the led lighting system has a built-in controller, no special timer is required for led lighting system.
-
Page 9: Warranty Card
Warranty card Lumen led lighting systems has a full warranty of 2 years and for the power supply is 5 years from the date of purchase. Save your invoice as proof of purchase. Complaints about led lighting systems that do not have an invoice will not be accepted. -
Page 10: Warranty Conditions
Lumen Aquatech always strives to repair or replace the device within a maximum of 15 days. If the manufacturer does not perform the repair or replacement within the period corresponding to his obligation, if he...
Need help?
Do you have a question about the LRW165 Series and is the answer not in the manual?
Questions and answers