Related Manuals for Kobelt 3905
Summary of Contents for Kobelt 3905
- Page 1 3905 QUICK RELEASE VALVE Owner’s Operation, Installation & Maintenance Manual Jan 2022 (Rev A)
- Page 2 3905 QUICK RELEASE VALVE Kobelt Manufacturing Co. Ltd. NOTES RECORD DATA BEFORE INSTALLATION FOR FUTURE REFERENCE Model #: Serial #: Date of Purchase: Date of Installation: Rev A MNL-3905.docx 2 of 14...
-
Page 3: Table Of Contents
3905 QUICK RELEASE VALVE Kobelt Manufacturing Co. Ltd. ABLE OF ONTENTS Introduction ......................4 Contact ........................4 Compliant Use ......................4 Copyrights & Trademarks ................... 4 Safety ........................5 Safety Alerts ....................... 5 Notice to Installer ....................... 5 Product Hazards ......................6 Product Description .................... -
Page 4: Introduction
Kobelt reserves the right, without notice, to change the design, or construction, of any products and to discontinue or limit distribution of any products. Kobelt also reserves the right to change, or update, without notice, any technical information contained within this document. -
Page 5: Safety
• Do not carry out any modifications to the product. • Only use authentic Kobelt spare parts. • Observe all local regulations, directives and laws during the installation of this product. • All installation, commissioning, and maintenance work must only be conducted by qualified personnel. -
Page 6: Product Hazards
Ensure all pressure is exhausted and power sources are locked out prior to performing work. RODUCT ESCRIPTION RODUCT ESCRIPTION The diagram below depicts a Kobelt release valve: Figure 1: 3905 Overview Diagram ECHNICAL PECIFICATIONS Table 1: Technical Specifications MODEL 3905 SUPPLY PRESSURE 200 psi [13.8 bar] MAX... -
Page 7: Schematic Symbol
3905 QUICK RELEASE VALVE Kobelt Manufacturing Co. Ltd. CHEMATIC YMBOL NSTALLATION ECHANICAL Mount the valve to a flat surface with enough rigidity to prevent excessive flexing from vibrations. When installing the mounting fasteners, it is recommended to use a thread locking product such as Loctite®... -
Page 8: Commissioning
3905 QUICK RELEASE VALVE Kobelt Manufacturing Co. Ltd. Do not over tighten the fitting in the ports as damage to the valve may occur. operation in sub-zero temperatures down to a minimum of 0 F [-20 C] the air must be... -
Page 9: Maintenance
3905-RK When purchasing spare parts refer to Appendix B: Parts List at the back of this manual for Kobelt component Part Numbers. See instructions at the end of this manual for shaft seal replacement. It is recommended that any required service work on a Kobelt product be performed by a factory authorized service representative. -
Page 10: Warranty
If any part is found to be defective, Kobelt will replace said part FOB the Kobelt factory provided that any such defective part is returned by the Buyer with freight and applicable forwarding charges prepaid by the Buyer. -
Page 11: Appendix A: Installation Dimensions
3905 QUICK RELEASE VALVE Kobelt Manufacturing Co. Ltd. A: I PPENDIX NSTALLATION IMENSIONS Figure 2: Installation Dimensions Rev A MNL-3905.docx 11 of 14... -
Page 12: Appendix B: Parts List
Figure 3: Parts Diagram Table 4: Parts List ITEM PART NO. DESCRIPTION 3905-0001 VALVE BODY, 3905 QUICK RELEASE 3905-0002 END CAP, 3905 QUICK RELEASE 3905-0003 PISTON, 3905 QUICK RELEASE 1001-1008 SCREW - HX HD; 1/4 UNC X 1/2 LG, 18-8 SPRING, COMPRESSION, 1.625 OD X .08 WIRE X... - Page 13 3905 QUICK RELEASE VALVE Kobelt Manufacturing Co. Ltd. Page Intentionally Left Blank Rev A MNL-3905.docx 13 of 14 Heiko Epkens Digitally signed by Heiko Epkens Date: 2022.01.27 15:39:51 -08'00'...
- Page 14 Kobelt Manufacturing Co. Ltd. 8238 129th Street Surrey, British Columbia, Canada, V3W 0A6 Sales Tel: +1-604-572-3935 Fax: +1-604-590-8313 Email: sales@kobelt.com Website: www.kobelt.com Made in Canada / Printed in Canada...