Operation; Installation; Wiring Diagram - golmar T-540 PLUS Quick Manual

DESCRIPTION
T-540 PLUS SE TELEPHONE
Digital telephone for the Plus system with button and coded door panels.
b
d
a
c
e
Connection terminals.
_ A D
+
+, - :
Positive, negative (18Vdc power supply).
A , D :
Audio, digital communication.
A P+ : Auxiliary door release button input.
HZ : - Door bell button input.
Function button.
With the handset on the hook and in standby: One short press for 1 second activates ringtone
volume mode, with a tone indicating the current volume selected. Then each 1 second press
"
(befor 5 seconds elapse) selects a volume level: maximum, medium, minimum and no volume
night mode and so on (in carousel mode).
" "
With the handset on or off the hook and in standby: One long press for 3 seconds turns the telephone on or off.
After any resetting of the telephone and for the following 45 seconds, no operation with it can be performed.
With the handset off the hook: The intercom (in the same apartment) is activated. One long press until a
( )
*
confirmation tone can be heard will call all of the telephones in the apartment. To call individual telephones,
press the button once to call the master telephone, twice to call slave 1 , 3 times to call slave 2 , 4 times to call
"
slave 3 and 5 times to call slave 4 . This selective intercom call mode is only available with the T540 Plus SE "
" " "
telephone and the Tekna Plus SE monitor. This only functions if no call or communication is in progress.
( ) Regardless of the position of the handset, the auxiliary device is activated.
*
With the handset on the hook: A panic call to the guard units configured to receive such calls is made. With the
handset off the hook, a normal call can be made to the main guard unit. During call reception and communication
processes, it enables the door release to be activated.
( ) In advanced programming mode, the default functions of function buttons
*
Quick programming SW1 DIP switch .
The quick programming SW1 DIP switch is located in the central part of the circuit, accessible by opening the
telephone. It enables the telephone to be configured as master/slave and an address to be assigned to it.
Important:This type of programming cannot be performed on a general entrance door panel.
Dip1 and Dip2: Configure the telephone as master/slave.
DIP 1 and DIP 2 to OFF master, DIP 1 to OFF and DIP 2 to ON slave 1, DIP 1 to ON and DIP 2 to OFF slave 2,
DIP 1 and DIP 2 to ON slave 3.
Dip3 a Dip10: To configure the telephone address.
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the
table below.
The telephone code is the sum of the values of the switches set to ON:
Switch number: 3 4
Value when ON: 128 64
Factory setting
Example: 0+ 64+0+16+0+4+2+1=87
Handset.
a.
Speaker grille.
b.
f
Microphone hole.
c.
Hueco de sujeción.
d.
Telephone cord connectors.
e.
g
Function / programming button.
f.
Telephone status LED:
g.
- Standby: LED illuminated red.
h
- Call: LED illuminated green.
(teléfono ppal.).
e
- Communication: LED illuminated green.
- Night mode: LED blinking red.
- Doctor mode: LED blinking green.
Hook switch.
h.
_
- SA + Int A1
AP HZ
+
SA : Output (negative) aux call repeater . , (m x. a
.
INT : Intercom function.
.
A : 1 Output (negative) auxiliary device activation
(max. consumption 50mA).
"
" " " "
and can be changed.
5 6 7 8 9 10
32 16 8 4 2 1
2

OPERATION

- Call reception: During call reception, the status LED of the master telephone will illuminate (green). If the call is not
answered within 45 seconds, the master telephone's status LED will illuminate (red), LED
off and the channel will be free.
- To establish communication, lift the handset of the telephone and the telephone's status LED (green) and the door
panel's LED will illuminate.
- The communication will last for one and a half minutes or until the handset is replaced. After the communication, the
telephone's status LED will illuminate (red), the door panel's LED will turn off and the channel will be free.
- To open the door, press the door release button during the call or communication processes: one press will activate the
door release for 3 seconds and LED

INSTALLATION

Connecting and fixing the telephone to the wall Avoid dusty or smoky environments or locations near sources of heat. The
telephone can be fixed to a universal embedding box or directly to the wall.
consumption 250mA).
Pass the cables through the cable holes and connect them to the connector.
Close the telephone as shown in the drawing. Once the telephone is closed,
connect the handset using the telephone cord and place it on the hook.

WIRING DIAGRAM

"
+ _
+ _
SW1
*
Place this power supply
as close as possible to the
first telephone.
FA-Plus/C or FA-Plus
PRI SEC
~ ~
+ +
Mains
IMPORTANT: F urther information about the door panel, sections, distances, wiring diagrams, etc., see T632 P
EN
https://doc.golmar.es/search/manual/ 5012
will also illuminate for 3 seconds.
:
Open the telephone by inserting a flat screwdriver into the slots and
gently pry open as shown in the drawing.
To fix directly to the wall, drill two 6mm holes at the specified positions
and use 6mm wall plugs and Ø3.5 x 25mm screws.
T-540 Plus SE
+ _
A D
T-540 Plus SE
+ _
A D
10
1
- -
2328
on the door panel will turn
T-540 Plus SE
A D
T-540 Plus SE
A D
Access panel
M =Master.
M
CN3 SW2
9 8 7 6
2 3 4 5
SW1
CN1
CV2 CV1 - + + - D A A V V V V
Malla
out in in- in+ out+ out-
DC lock release
lus P/T User Manual .
" "
EN
3