WARNING CAUTION ADULT ASSEMBLY REQUIRED PARENTAL SUPERVISION IS REQUIRED IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater.
Page 3
WARNING CAUTION NEVER use a wall mount bracket from another manufacturer. This product is not intended to be a primary heat source. It is for supplemental heat only. INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock! ...
COMPONENT PARTS Please check that you have all the parts listed below 1. Fireplace firebox x1 2. Fireplace Front Glass Panel x1 3. Wall Bracket - at back of firebox x1 4. Metal Bracket x1 5. Firelog setx1 6. Decorative Crystals x1 7.
INSTALLATION Your appliance is a wall-mounted, recessed and/or mantel installed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas. NOTE: FOLLOW ALL NATIONAL AND LOCAL ELECTRICAL CODES. MINIMUM CLEARANCE TO COMBUSTIBLES Measurements are taken from the glass front 8”...
Page 6
INSTALLATION RECESSED WALL INSTALLATION Remove four silver screws from the sides of the heater, two screws on each side. Remove two screws from the front of the heater. Remove the tempered glass by lifting it from the lugs on the sides. Remove two screws from the mounting bracket part 3 on the back of the part 1, then remove the part 3.
Page 7
INSTALLATION RECESSED WALL INSTALLATION CONTINUED Poristion the part 3 on the wall and mark where the eight screw holes will be. Make sure that the bracket is level. Use an electric drill and size 6 drill bit to drill 8 screw holes. Insert eight 4×30mm wall anchors C into holes,then attach the part 3 to the wall with eight 4×30mm screws.
Page 8
INSTALLATION RECESSED WALL INSTALLATION CONTINUED Lift the part 1 and carefully lower it onto the part 3,ensure that bracket and heater are firmly engaged. Insert a wall anchor C and attach bottom bracket 4 with 4×30mm screws. Page 8 of 17...
Page 9
INSTALLATION RECESSED WALL INSTALLATION CONTINUED Attach the bottom bracket 4 to the part 1 with two 4×30mm screws. Put the crystal stones 6 to enber bed.First, take off glass (part 2) from appliance(part 1). Then put crystal stones 6 on ember bed. Page 9 of 17...
Page 10
INSTALLATION RECESSED WALL INSTALLATION CONTINUED Place the part 2 surround over the front of the fire aligning the slots in the bracket at each side of the glass panel with the lugs on the sides of the fire. Again, two persons will be required for this operation. Last, fix the tempered glass with 4 pcs of 4×8mm white screws on both sides as provided.
INSTALLATION WALL MOUNTED INSTALLATION The switches located at the center right hand side of the fire.The standby switch must be first switch on Take the glass (part 2) from the appliance first,then gently put the appliance the cut hole by two persons please. For optimum viewing, mark the left and right screws (fixing positions on the wall in accordance with the appliance’s holes.
Page 12
INSTALLATION WALL MOUNTED INSTALLATION Place the front glass surround over the front of the fire aligning the slots in the bracket at each side of the glass panel with the lugs on the sides of the fire. Again, two persons will be required for this operation. Fix the tempered glass with 2 pcs of 4×8mm screws provided.
OPERATION WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure do to so could result in electric shock, fire, serious injury, or death. POWER Plug the power cord into a 110-120V Volt 12 Amp grounded outlet (see IMPORTANT SAFETY INFOR- MATION on pages 2, &...
TOUCH PANEL & REMOTE CONTROLS BUTTON FUNCTION ACTION & INDICATION ON: Enables control panel functions and remote ON - Press once. Indicator light turns on. control. Powers on flame effect. Power turns on. All functions enabled. OFF: Disables control panel functions and remote OFF - Press once.
APP | CARE & MAINTENANCE CONNECT WIFI Download App You can download the App by searching “Tuya Smart” in mobile app stores or scanning the following QR code. Keep the appliance Master power switch turned on Kindly check our user manual to learn how to connect the Tuya Smart App NEVER dispose of batteries in fire.
MAINTENANCE & TROUBLESHOOTING Electrical and Moving Parts: The fan motors are lubricated at the factory and will not require lubrication. Electrical components are integrated in the fireplace and are not serviceable by the consumer. Storage: Store heater in a clean dry place when not in use. ...
Page 17
ASSEMBLY COMPLETE CONGR TUL TIONS, OUR NAOMI HOME CYRA ELECTRIC FIREPLACE IS COMPLETE! Product Packaging Information Model #: ________________________________ Color: __________________________________ ® Shipment Ref. #: _________________________ www.NaomiHome.com Date: __________________________________ MADE IN CHINA Page 17 of 17...