Advertisement
Device Installation/ 设备安装
A.
(Optional) SD Card and Wi-Fi Antenna Installation/ 安装 SD 卡 & 安装 Wifi 天线
Install the SD card: Use the Phillips screwdriver to remove the camera bottom cover, and insert the SD card. You
can refer to the SD card icon on the maintenance window for the insertion direction. During SD card installation,
you are advised to turn the camera maintenance window downward and insert the SD card into the SD card slot
from below to avoid accidentally dropping the SD card into the camera.
Install the Wi-Fi antenna: Install the O-ring of the antenna in the screw hole of the antenna on the camera and
tighten the antenna.
安装 SD 卡：用十字螺丝刀将摄像机底盖卸下，插入 SD 卡，SD 卡插入方向参考维护窗上标识。安装 SD 卡时，建议将摄像
机维护窗朝下 , 避免不慎将 SD 卡掉入摄像机内部，造成设备故障。
安装 Wifi 天线：先将天线的密封圈安装到摄像机的 Wifi 天线螺孔位置，再将 Wifi 天线拧紧到摄像机上。
Install the SD card
安装 SD 卡
Install the Wi-Fi antenna
安装 Wifi 天线
B. Beam-Mounted Installation/ 横臂安装
Install the universal joint (here, a three-dimensional universal joint is used as an example) into #2 holes (for the
1
#2 hole identifier, see the silk screen on the physical device) on the pole mount. Unfasten the screws on the
universal joint to enable the universal joint to rotate freely. Adjust the horizontal and vertical shooting angles
and tighten all screws on the universal joint.
以三维万向节为例进行介绍，将万向节安装到抱装支架 2 号孔位（2 号孔位标识请参见实物上的丝印）。通过标识 1 位置
的螺钉将摄像机固定在万向节上，并初步调整好水平和垂直监控角度，拧紧万向节上的所有螺钉。
NOTE/ 说明
a: Loosen the screw here. Then, you can adjust the tilt angle of the camera.
b: Loosen the screw here. Then, you can adjust the horizontal angle of the camera.
c: Loosen the screw here. Then, you can adjust the vertical angle of the camera.
a：通过拧松该处螺钉，可调节摄像机倾斜角度。
b：通过拧松该处螺钉，可调节摄像机水平角度。
c：通过拧松该处螺钉，可调节摄像机垂直角度。
1
CAUTION/ 注意
• Before installing the camera on the pole,
install the SD card and Wi-Fi antenna.
请在摄像机上杆前，安装SD卡和Wifi天线。
• Do not remove the protective film from the lens
before the installation is complete.
安装完成前切勿撕下镜头保护膜。
c
b
a
B. Beam-Mounted Installation/ 横臂安装
Unfasten the three hose clamps and thread them through the installation holes on the pole mount. Place the
2
hose clamps around the beam and tighten them up. Adjust the surveillance angle. Fasten all screws on the
universal joint and use captive screws to fasten the two planes of the universal joint to fix the universal joint.
Then, adjust the position of the sunshield.
将 3
个喉箍环穿过抱装支架的安装孔，并环绕在横臂上，拧紧喉箍。调整好监控角度，拧紧万向节上的所有螺钉，再使
用辅助紧固螺钉在万向节的两个面上拧紧，使万向节固定，最后调整好 d 处遮阳板的位置。
d
c
C. Pole-Mounted Installation/ 抱柱安装
Install the wall mount into #5 holes on the pole mount (for the #5 hole identifier, see the silk screen on the
1
physical device).
将壁装支架安装到抱装支架 5 号孔位（5 号孔位标识请参见实物上的丝印）上。
3
NOTE/ 说明
If a two-dimensional universal joint
is used, you can refer to the pole-
mounted installation procedure to
install the universal joint and adjust
its angle.
若使用的是二维万向节，万向节的安装
和角度调整方式，可参考抱柱安装过程
进行安装。
zhej
Advertisement
