Subscribe to Our Youtube Channel
Related Manuals for AquaStar Statztruck
Summary of Contents for AquaStar Statztruck
- Page 1 InstallatIon manual automatic suction pool cleaner 877.768.2717 fax: 877.276.POOL (7665) Outside the U.S.: +1.805.620.5060 fax: +1.949.336.1940 www.aquastarpoolproducts.com info@aquastarpoolproducts.com...
- Page 2 Thank you for purchasing the Statztruck automatic pool cleaner. Aquastar proudly manufactures and assembles all of their products in the U.S. The Starztruck automatic pool cleaner works from the suction side of your pool filter - subject to the GPM (gallons per minute) of the suction line. For technical assistance, call Aquastar Pool Products at 877.768.2717.
- Page 3 1: connectinG and submerGinG the hoses and cleaner There are seven connector hoses. The hose cuff on any of the hose sections connects to the top of the StarzTruck automatic pool cleaner (see Fig. 1). Connect the StarzTruck automatic pool cleaner hose sections together by pushing and twisting the tapered male connector end of each hose firmly into the open female end of the adjacent hose section (see Fig. 2). Depending on the size and shape of your pool, all hose sections might not be used. The hose should reach from the skimmer or safety vacuum lock wall fitting (AquaStar p/n VLK15Txx) to the furthest point in the pool plus one extra hose section. If the hose is not long enough, it will be necessary to purchase additional hose sections from your pool dealer. After the correct hose length has been assembled, fill the hose completely with water by lowering the attached StarzTruck automatic pool cleaner and then vertically pushing the hose down, allowing all the air to escape. When the hose is full, remove the StarzTruck automatic pool cleaner from the hose and insert the flow gauge into the leader hose. Make sure the flow gauge is under water (see Fig. 3).
- Page 4 step 2: connectinG to suction Connect a skimmer cone adapter and then insert the skimmer cone into: A. The suction port of the skimmer (see Fig. 5) or B. The wall port safety vacuum lock without a three-way or ball valve (see Fig. 6) or C. Without the skimmer cone and regulator valve – insert the male end of the hose directly into the safety vacuum lock wall fitting port – with a three-way or ball valve (see Fig. 7) VLK15Txxx safety To StarzTruck Hose vacuum lock wall fitting Skimmer HWN161 regulator valve HWN152 cone adapter Fig. 6 To pump To main drain (if applicable) VLK15Txxx safety Fig.
- Page 5 3: adjustinG Your starztruck automatic pool cleaner Check the water flow reading on the Flow Gauge (refer to step 1, Fig. 3). The black disk should be in the box between the “MIN” and “MAX” markings. If the setting is higher than required with the black disk outside of the box on the “MAX” side and you have connected your hose to the skimmer, it will be necessary to reduce the vacuum/water flow by using a valve or valves in the filter system, or the AquaStar hwn161 Regulator Valve or an optional AquaStar Automatic Skimmer Vacuum Plate designed to adjust vacuum/ water flow. To install the hwn161 Regulator Valve, turn the filter system off. Remove the hose from the hwn152 Skimmer Cone, and after closing the Regulator Valve (rotate the blue collar clockwise/toward + until closed/tight), insert the Regulator Valve into the Skimmer Cone, and insert the hose end into the Regulator Valve (see Fig. 5 on previous page). Turn the filter system on and allow it to run long enough to eliminate any air in the system. Turn the blue collar counter clockwise until the proper reading appears on the gauge. If you have connected your hose to the AquaStar Vacuum Lock, it will be necessary to adjust the vacuum/ water flow using the three-way valve at the filter system. The handle on the valve should be turned so that the Flow Gauge which is installed in the StarzTruck hose reads properly (refer to Fig. 3 on page 2). After the three-way valve has been properly adjusted, the vacuum gauge at the three-way valve should be marked so that the water flow can be adjusted by referring to the gauge at the valve rather than reinstalling the Flow Gauge in the hose each time an adjustment is necessary. Once the Flow Gauge has a proper reading, remove it from the leader hose and reattach the StarzTruck automatic pool cleaner. Submerge the StarzTruck back into the pool until it reaches the bottom for operation.
- Page 6 step 3: adjustinG Your starztruck automatic pool cleaner continued Some skimmers have a vari-flow or diverter valve in the bottom of the skimmer. This valve can be turned to regulate skimming and main drain suction. Turn the valve to full skim and then adjust the Flow Gauge vacuum gauge by turning the valve toward main drain suction. Usually this valve is the same size as the hose end, and it will therefore be necessary to purchase an hwn158 Hose Connector (see Fig. 8). After the proper gauge reading has been established, the diverter valve will have to be locked in place with a wedge of some kind so that it won’t change position with operation of the StarzTruck. Periodically check the water flow/vacuum to be sure that the StarzTruck is operating as efficiently as possible. Remember, too much vacuum is just as bad as too little. Periodically check to make sure that the StarzTruck hose is securely attached to its suction source (i.e. Skimmer, Skimmer Vacuum Plate, Safety Vacuum Lock, etc.). Disconnect the StarzTruck hose from the skimmer/regulator valve, or, if using a dedicated line, turn cleaner valve off before backwashing, so that you’re not restricting water flow. Never coil the StarzTruck hose. Damage caused by coiling the hose is not covered under the warranty. When the StarzTruck is out of the pool, always disconnect the leader hose from the StarzTruck head. Always carry the StarzTruck by the molded-in handle. Do not carry it by the hose. When swimming in the pool, remove the StarzTruck from the water. If you are going to super-chlorinate, shock or add gas chlorine to your pool, make sure the cleaner and hose are removed before doing so. To StarzTruck Hose Optional hose adapter Skimmer diverter valve To pump To main drain Fig.
- Page 7 step 3: adjustinG Your starztruck automatic pool cleaner continued The StarzTruck automatic pool cleaner will climb vertical walls in concrete and fiberglass pools (not vinyl) if there is at least a 12-inch radius where the floor meets the walls. Because of the internal programmed gear box, the cleaner will not climb the wall every time. Likewise, it will not always go all the way up the wall. If the StarzTruck automatic pool cleaner is not sticking to the wall, set the rear flap to position III (see Fig. 9) and/or adjust your regulator valve(s). If the cleaner climbs above the waterline and sucks air, set the rear flap to position I (see Fig. 10) and/or adjust your regulator valve(s). Rear flap tension adjuster Fig. 10...
- Page 8 CAUSES SOLUTIONS Lack of/improper water flow through cleaner Check and adjust water flow per step 3, Figs. 7, 8, 9, 10 Partial blockage of StarzTruck throat Clear blockage Worn shoes Replace shoes Worn wings Replace wings problem: cleaner fails to climb vertical walls Gunite/concrete pool CAUSES SOLUTIONS Improper shoes for application Call AquaStar Lack of/improper water flow through cleaner Adjust water flow per step 3, Fig. 10 Partial blockage of StarzTruck throat Clear blockage Worn shoes Replace shoes Worn wings Replace wings Hose too short Install additional hose sections per installation Instructions Improper tension on rear flap Turn rear flap adjuster to III...
- Page 9 starztruck automatic pool cleaner troubleshootinG Guide problem: cleaner climbs to surface and sucks air CAUSES SOLUTIONS Too much/improper water flow through cleaner Check and adjust water flow per step 3, Figs. 7, 8, 9, 10 Improper tension on rear flap Turn rear flap adjuster to I If still climbing too much, reduce water flow until proper operation is achieved Steering failure 1. Check and clean rear screen 2. Check to see that cone gear is free and rotates smoothly in both directions 3. Check medium turbine and spindle gear assemblies for malfunction problem: cleaner head floats CAUSES SOLUTIONS Cleaner head or return line has air in it Remove all air from cleaner head Stop all air from entering the pool through the return lines If cleaner head and hose are covered with fine...
- Page 10 A. Pool plaster is affected by age, water chemistry, etc. G. Vinyl can also be affected by the installation and the pool’s surroundings. B. Pool plaster can deteriorate over a period of time. H. W hen installing the StarzTruck automatic pool cleaner, C. T he integrity of “good” pool plaster is such that a pool you assume all responsibility for the condition of the pool vacuum cleaner – automatic or manual – cannot remove and the pool’s surroundings. that plaster. To better serve you, please have the following information D. T he integrity of “good” pool plaster is such that the available if you call AquaStar’s Technical Support Department: plaster will cause wear on the StarzTruck automatic pool cleaner – not vice versa. 1. The purchase date and purchase location of your StarzTruck automatic pool cleaner. E. Vinyl and fiberglass are affected by age, sunlight and water chemistry. 2. The serial number of your StarzTruck automatic pool cleaner. F. Vinyl can become brittle and weak. 3. The number of hose sections used.
- Page 11 StarzTruck automatic pool cleaner’s operation. at no additional charge except as set forth below. Repair 7. This limited warranty does not cover damage or injury parts and replacement products will be furnished on an from improper installation, pump running dry, damage exchange basis and will be new or functionally equivalent. due to loss of prime or plugged pipes. All parts removed as a result of replacement shall become 8. This limited warranty does not cover any change in the property of AquaStar. Liability of AquaStar and the appearance, damage, malfunction due to chemical sole remedy of the purchaser whether in contract under reactions, etc. any warranty, in tort (including negligence), in strict liability or otherwise, shall be limited to the repair or 9. AquaStar is not responsible for any loss of time, replacement of defective parts only and shall in no event inconvenience or any consequential expenses such as exceed return of the amount of the purchase price paid by telephone calls, labor, etc., unless required by law. the purchaser. 10. Deterioration, discoloration or brittleness of pool plaster 2. This limited warranty is for the replacement of alleged and vinyl liners can be caused over time separately by defective parts during the term of the warranty; owner or in combination with, age and an imbalance in pool may ship the product by prepaid freight to AquaStar water chemistry, improper installation and other factors. Pool Products, Inc., 2340 Palma Drive, Warranty Dept. AquaStar hereby disclaims any and all claims, and 104, Ventura, CA 93003, USA. Enclose a letter including purchaser releases AquaStar from any and all claims for the serial number, date and place of purchase, name, damages to any pool plaster or vinyl liner in purchaser’s...
-
Page 12: Warranty Registration Card
6. Pool is _ ______________ years old. o Vinyl o Fiberglass 7. What cleaner is this replacing? o Gunite ______________________________________________________ o Other 8. Are you a: 3. Cleaner model: o Consumer o Concrete o Pool Service Technician o Vinyl/fiberglass o Pool Builder o Other 4. Date of purchase: __________________________________ Please complete and mail with receipt to: Or fax to: AquaStar Pool Products, Inc. 877.276.POOL (7665) Warranty Registration Dept. 104 Outside the U.S.: +1.949.336.1940 2340 Palma Drive Ventura, CA 93003...
Need help?
Do you have a question about the Statztruck and is the answer not in the manual?
Questions and answers