Page 1
FITNESS PLAYGROUND ITEM NO: 8101 OWNER’S MANUAL CAUTION: This unit is designed to be used safely by up to 6 children between the ages of 3 years to 8 years old with a maximum weight of 100 pounds (45.4kgs) each, simultaneously, not to exceed a combined weight of 600 pounds (272kgs).
Page 2
IMPORTANT: FOR NORTH AMERICA ONLY To request product service and order replacement parts, please call our customer service department at: 1-866-924-1688 Monday through Friday, 8:00 AM-5:00 PM Pacific Standard Time, service@paradigmhw.com or email us at: Please visit our website at www.paradigmhw.com. Please have the following information ready when requesting for service: Your name Phone number...
MANUFACTURER’S LIMITED WARRANTY (IRONKIDS FITNESS PLAYGOUND) Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has be installed and operated in accordance with Paradigm’s Owner’s Manual.
IMPORTANT SAFETY PRECAUTIONS Read all instructions carefully before assembling operating this product. Retain this owner’s manual and keep the original purchase receipt for future reference. Before you assemble the Fitness Playground, find level ground not less than 6 feet from any structure or obstruction to the Fitness Playground.
CARE AND MAINTENANCE Check all nuts and bolts by monthly during the usage season for tightness and tighten as required. It is particularly important that all nuts and bolts are checked prior to the first use each season. TOOLS REQUIRED FOR ASSEMBLY Please prepare the following tools prior to assemble this equipment.
PARTS NUMBERS AND ILLUSTRATIONS Parts used for main frame assembly Side Top Bar 2 PCS Top Bar 1 PC Leg with Foam 1 PC Leg with Foam 1 PC 1 PC 1 PC Cross Bar 1 PC Cross Bar 1 PC Ground Anchor 8 PCS...
Page 10
Hardware used for main frame assembly Bolt 5/16”x63 8 PCS Bolt 5/16”x68 4 PCS Nylon Nut 5/16” 12 PCS Plastic Cap 12 PCS Curve Washer 8 PCS Large Washer 4 PCS Sunshade 1 PC Plastic Stick 2 PCS Protective Net 1 PC...
Page 11
Parts used for trampoline assembly Protective Net 1 PC Jump Mat 1 PC Frame Pad 1 PC L-Shaped Tube (Left) 1 PC L-Shaped Tube (Right) 1 PC Straight Tube 1 PC Handlebar with Foam 1 PC Handlebar Base Tube (Left) 1 PC Handlebar Base Tube (Right) 1 PC...
Page 13
Parts used for trapeze assembly Trapeze Tube 1 PC Eye Bolt with Attachment Bolt 2 PCS Rubber Cap (Preassembled) 2 PCS Hardware used for trapeze assembly Nylon Nut 5/16” 2 PCS Plastic Cap 2 PCS...
Page 14
Parts used for swing seats assembly PVC Covered Chain 4 PCS (Preassembled) Eye Bolt with Attachment Bolt 4 PCS (Preassembled) Swing Seat 2 PCS Eye Bolt with Attachment Bolt 4 PCS (Preassembled) Hardware used for swing seats assembly Nylon Nut 5/16” 8 PCS Large Washer 4 PCS...
Page 15
Parts used for slide assembly Slide Support (With Opening) 1 PC Slide Support 1 PC Slide Leg Tube 2 PCS Slide Top Support Bar 1 PC Slide Front Support 1 PC Slide Ladder Steps 2 PCS Slide 1 PC Cap for X4 (Preassembled) 2 PCS Linking Bar 1 PC...
Page 16
Hardware used for slide assembly Plastic Connector 2 PCS Bolt 1/4”x38 6 PCS Bolt 1/4”x45 2 PCS Screw M6x40 2 PCS Spring Washer 4 PCS Nylon Nut 1/4” 4 PCS Cap Bolt 1/4”x14 4 PCS Spring Washer 20 PCS Bolt 1/4”x75 2 PCS Screw M6x45 4 PCS...
ASSEMBLY INSTRUCTIONS l Place the playground equipment on level ground, not less than 6 feet (1.8 meters) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. l Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface.
Page 19
Round hole Concave hole faces up faces down NOTE: Do not over-tight the nuts and bolts. Do not snap the plastic cap on until you have completed the rest of the assembly and have tightened the nuts and bolts. Step 1 Insert A2 into A1, secure with B1, B5, B4, and B3.
Page 20
l Align the holes and secure using B1, B5, B4, and B3. Step 3 l Insert the small end of T8 into the socket of A3 and A3A and align the holes. (Socket of T8 faces outside.) l Secure using T15, T18, and T13. Attach A6 onto A3 and A3A with two B2, two B6, two B4, and two B3.
Page 21
l Secure using B2, B6, B4, and B3. l Repeat the same procedure onto the right outer side of A4A. Step 5 l Attach T1 onto A3, A3A, A6, and T8 with the Velcro straps on the sides of T1. Step 6 l...
Page 22
Step 7 l Put T7A onto the outside of T4A, and put T7B onto the outside of T4B, align the holes. l Secure using T10, T12, T19, and T14 for the upper hole of T7A and T7B. l Secure using T11, T12, T19, and T14 for the lower hole of T7A and T7B. Note: The T10’s are longer than the T11’s.
Page 23
Drop hook into the frame hole until it latches on. Note: BE CAREFUL NOT TO PINCH HANDS OR FINGERS ON SPRINGS. USE GLOVES TO PREVENT PINCHING. KEEP SPRINGS DRY; WET SPRINGS ARE VERY SLIPPERY. Step 9 l Insert two corners of T3 which have yellow banners to the small end of T7A and T7B. Lay the Frame Pad (T3) over the trampoline, so that the springs and the steel frame are covered.
Page 24
Step 10 l Insert small end of T7A and T7B into the small end of T6, align the holes. l Secure using with T17. Note: Go back to tighten the screw from STEP 7. Step 11 l Bring one end of the strap on T3 which is near to the jumping mat T2, then tie the strap to the triangle ring with a knot.
Page 25
Step 12 l Insert J2 into holes on A2. l Secure it with J8 and J6. Step 13 l Attach K1 to J3. Secure with J7 and J6. l Step 14...
Page 26
l Attach P1 to S1. l Attach S1 to A2. l Secure using S3 and S2. Bolt hole faces up Step 15 l Attach X5 to Y2. l Secure using Z7 and Z9. l Attach X4 to Y2. l Secure using Z3 and Z7. Note: Make sure that the bolt holes face up.
Page 27
Step 16 Attach X6 to X1 and X2. l l Secure each side using Z1, Z7, and Z5. l Attach X3 to X1 and X2. Align holes and hold in position. l l Insert Z1 into Z7 and insert into X1, X2, X7, and X3 as shown. Step 17 l...
Page 28
Step 18 l Attach Y1 to X1 and A5, secure using Z8, Z7, Z4, and Z6. Note: Make sure to go back to check all hardware and securely tighten all bolts and nuts before using the playground equipment. Warning: Do not let children use the playground equipment until it is properly assembled and anchored.
GROUND ANCHOR INSTALLATION You may either anchor the feet in hard soil or if your soil is soft (sand, etc.), you may use the corkscrew (A7) anchor to secure the playground. If you wish to permanently secure your swing set, setting the legs in concrete secured by a brick or gravel bed is recommended.
Page 30
For Concrete Ground Installation: l If the swing set is set up on grounds with sandy soil, it must be anchored with concrete footing (concrete not included). Dig holes around swing leg tube as shown below in drawing. As you dig down and create a l...
If the swing set is used without proper anchoring, it may be dangerous and may tilt over. This play ground received ASTM F2276 and CPSIA certification. IRONKIDS PARTS REQUEST FAX FORM Please fax this form to (1-626-810-2166) OR YOU CAN EMAIL CUSTOMER SERVICE REQUESTS TO service@paradigmhw.com...
Page 32
OFFICIAL USE ONLY SHIP DATE: ___________________________________________ TRK #: _______________________________________________ BACK ORDER: ________________________________________...
Need help?
Do you have a question about the 8101 and is the answer not in the manual?
Questions and answers