Related Manuals for Schweißkraft VarioProtect PANORAMA-W S-TC
Summary of Contents for Schweißkraft VarioProtect PANORAMA-W S-TC
- Page 1 Operating Instructions Automatic Welding Helmet VarioProtect PANORAMA-W S - TC VarioProtect PANORAMA-W R - TC VarioProtect PANORAMA-W R - TC VarioProtect PANORAMA-W S - TC...
-
Page 2: Table Of Contents
Imprint Content Product identification 1 Introduction............ 3 1.1 Copyright ............3 Automatic Welding Helmet Item number 1.2 Customer service..........3 1.3 Limitation of liability..........3 VarioProtect PANORAMA-W S - TC 1654060 2 Safety.............. 3 VarioProtect PANORAMA-W R - TC 1654070 2.1 Symbol explanation .......... -
Page 3: Introduction
Introduction Introduction 1.3 Limitation of liability All information and notes in these operating instructions You have made a good choice by purchasing the were summarised while taking applicable standards and Schweißkraft welding helmet. rules, the state-of-the-art technology and our long-term knowledge and experiences into consideration. -
Page 4: Safety Regulations
Safety - Check the Automatic Welding Helmet for externally visible damage and defects before putting it into CAUTION! operation. This combination of symbol and signal words indi- - Repair any defects and damage immediately. cates a potentially dangerous situation which may - Do not use the Automatic Welding Helmet in damp lead to slight or minor injury if not avoided. -
Page 5: Intended Use
Intended Use Intended Use Technical Data The Automatic Welding Helmet VarioProtect PAN- VarioProtect PANORMA S-TC ORAMA-W S - TC and VarioProtect PANORAMA-W R - TC protect the eyes and face from sparks, splashes and R-TC harmful radiation under normal welding conditions. It is Length x Width/Depth x 249 x 298 x 334 suitable for use in MIG/MAG, TIG and electrode welding. -
Page 6: Description Of The Helmet
Description of the Helmet Description of the Helmet VarioProtect PANORAMA-W S - TC and VarioProtect PANORAMA-W R - TC Fig. 2: helmet A Front protection plate / Outer pane B Peripheral perception filter C Snap lock of the protective pane D Snap locking device of the protective pane E Helmet shell F Automatic darkening filter... - Page 7 Description of the Helmet 1 Operating mode switch 2 Headband for adjusting helmet distance 3 Viewing window 4 Setting of the protection levels 5 Filter cartridge 6 Battery compartment 7 Setting of sensitivity (SENSITIVITY) 8 Setting of the brightening time (DELAY) 9 Battery control indication 10 Welding helmet identification (SWM 175 F CE) 11 Side window, welding protection filter for peripheral...
-
Page 8: Wearing Parts
Transport, Packaging, Storage Transport, Packaging, Storage 1 Sweatband 2 Front headband 3 Right band 6.1 Transport 4 Left band 5 Rear headband 6 Rear headband adjustment wheel Check the welding helmet on delivery for any visible trans- 7 Flat washer portation damage. -
Page 9: Product Characteristics / Setting Options
Product Characteristics and Setting Options Product Characteristics and Setting 7.2 Setting the sensitivity Options The sensitivity can be regulated with the rotary switch SENSITIVITY. LO means minimum sensitivity and HI me- The shape of the helmet relieves the welder's head and ans maximum sensitivity. -
Page 10: Headband Adjustment Options
Product Characteristics and Setting Options Adjust distance between viewing window and face: The distance to the viewing window can be adjusted by pressing the lateral pins and simultaneously moving the sliders. There are 5 distance positions available for adju- stment. See figure 8c. Side buttons Fig. -
Page 11: Notes Before Commissioning
Notes before Commissioning - Always check the helmet and filter lens before wel- ding to ensure they are in good condition, undama- ged and properly fitted. - Check that the clear lens is clean and securely at- tached to the helmet. - Always wear safety glasses under the welding hel- met and protective clothing to protect your skin from radiation, burns and splashes. -
Page 12: Operation
Operation - People with particularly sensitive skin must be - The operating temperature range is between -5 ° C especially careful: Materials that can come into and 55 ° C. When the ambient temperature is contact with the skin can cause allergic reactions. below the lower limit, the response speed of the li- quid crystal materials of the lens is slightly lower, - Check that the protection level corresponds to your... -
Page 13: Troubleshooting
Troubleshooting 11 Troubleshooting Problem Possible Cause Solution The filter does not darken or is The external transparent protection Replace the external transparent unstable when switching from light to of the filter is dirty or damaged. protection. dark and back again. The sensors are dirty. -
Page 14: Color Table
Color Table 12 Color Table Recommended color chart according to EN 169. Depending on the environmental conditions, it is possible that smaller or larger color tones have to be selected. Fig. 11: Color table VarioProtect PANORAMA - Serie | Version 2.02 | EN... -
Page 15: Meaning Of The Marking
Meaning of the Marking 13 Meaning of the Marking Each product is marked with a corresponding protection level (DIN 4 to DIN 8 and DIN 9 to DIN 13). Make sure that the correct protection level has been set before star- ting the welding process. -
Page 16: Care, Maintenance And Repair
Care, Maintenance and Repair 14 Care, Maintenance and Repair WARNING! Danger in case of insufficient quali- fication of persons! Insufficiently qualified persons cannot evaluate the risks to the user resulting from improper repair work on the welding helmet and expose themselves and others to the risk of serious injury. -
Page 17: Replace The Battery
Care, Maintenance and Repair 14.3 Replace the battery Gently push the battery covers away to the outer sides until they are open. Remove the old batteries from the battery compartment. Insert new batteries and close the battery compartment again. Fig. 15: Battery replacement 14.4 Replacing the filter cassette Step 1: To release the filter cassette, unscrew the knurled screw 26 (Fig. -
Page 18: Maintenance/Repair
Disposal, Recycling of used Devices - Do not put heavy tools / objects in or on the helmet to avoid damaging the filter or the protective screens. - Keep the helmet away from flames. - Do not allow the helmet to fall down. - Do not place the helmet too close to the welding area. -
Page 19: Spare Parts
Spare Parts 16 Spare Parts Example The outer pane for the welding helmet VarioProtect PAN- ORAMA-W S - TC must be ordered. The outer pane has DANGER! the position number 18 in the spare parts drawing 1. Danger of injury by the use of wrong spare parts! When ordering spare parts, send a copy of the spare Dangers may result for the user and damages as... -
Page 20: Spare Parts Drawing
Spare Parts 16.2 Spare parts drawing The following drawing should help you to identify necessary spare parts in case of service. If necessary, send a copy of the parts drawing with the marked components to your dealer. Spare parts drawing VarioProtect PANORAMA-W S - TC and VarioProtect PANORAMA-W R - TC Fig. -
Page 21: Eu - Declaration Of Conformity
EU - Declaration of Conformity 17 EU - Declaration of Conformity Manufacturer/ Distributor: Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Straße 26 D-96103 Hallstadt hereby declares that the Personal Protective Equipment (PPE) described below complies with the provisions of the PPE Regulation 2016/425/EU and the Product Safety Directive 2001/95/EC , and is identical to the PPE that is the subject of the test performed by the accredited testing institute. - Page 22 www.schweißkraft.de...
Need help?
Do you have a question about the VarioProtect PANORAMA-W S-TC and is the answer not in the manual?
Questions and answers