Function Table Of Ic - Sharp MD-MT270HS/BK Service Manual

IC401 RH-iX0561AWZZ :System Microcomputer (IX0561AW) (1/2)
Pin No. Port Name Terminal Name Input/Output
1* P9_4/DA1 MCMON
2 P9_3/DA0 LDVAR
3 P9_2 EPRT
4 TB1IN SPIN
5 TB0IN CIN
6 BYTE VSS
7 CNVSS VSS
8 P8_7 RCLAT
9 P8_6 SYCPW
10 RESET _RESET
11 XOUT EXTAL
12 VSS VSS
13 XIN XTAL
14 VCC VCC
15 P8_5/NMI NMI
16 INT2 _DINT
17 INT1 _PLAY
18 INT0 _REC
19* P8_1/TA4IN
20 P8_0 RCPCNT
21 TA3IN _RPLAY
22 P7_6
23 P7_5 PBOPON
24 TA2OUT BUZOUT
25* P7_3 CHGON
26 P7_2/TA1OUT
27* P7_1/TB5IN
28* P7_0/TA0OUT
29 P6_7/TXD1 DSPDAT
30 P6_6/RXD1 DSPSTB
31 P6_5/CLK1 DSPSCK
32* P6_4 TEST0
33 P6_3/TXD0 RMDAT
34 P6_2/RXD0 PCILD
35* P6_1/CLK0 SCK0
36 P6_0 OPICGA
37 P5_7/CLKOUT PCLK
38 P5_6 SGAIN
39 P5_5 DISCP
40 P5_4 JPNP
41* P5_3
42* P5_2
43 P5_1 RACLK
44* P5_0 TEST1
45 P4_7 _MCPGI
46 P4_6 _INPGI
47 P4_5 INPGCK
48 P4_4 SENSE
49 P4_3 SLCNT1
50 P4_2 SLCNT2
In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside.

FUNCTION TABLE OF IC

Output Internal operation status monitor
Output P.U. laser power setting output
Output EEPROM write protection
Input/Output Spindle motor FG pulse detection input
Output Track cross signal/focus drive detection
— Ground potential
— Ground potential
Output Record audio IC data latch output
Output System LSI core power on/off
Input Microcomputer hard reset input
— Crystal connection terminal
— Ground potential
— Crystal connection terminal
— Positive power supply
Input Nonmaskable interruption input (not used)
Input System LSI interruption
Input Unit PLAY button operation detection input
Input Unit REC button operation detection input
Output Reserve
Input/Output Record circuit power control output
Input Remote control PLAY key operation detection input
Output Reserve
Output Audio IC output stage control output
Output Beep sound pulse output
Output Battery charge ON/OFF control output
Output Reserve
Output Reserve
Output Reserve
Output Unit indication data output
Output Main unit display strobe output
Output Unit indication data clock output
Input Test mode setting input 0
Output Remote control indication data output
Input/ IF data input
Output Serial I/O clock output (not used)
Output P.U detection sensitivity switching output
Output Power clock
Output RF amp gain polarity switching output
Output RF amp TE polarity switching output
Input Kana conversion/Kana input existence/nonexistence discrimination
Output Reserve
Output Reserve
Output Audio IC data clock output
Input Test mode setting input 1
Input Microphone plug insertion detection input
Input Line/digital plug insertion detection
Input Line/digital plug type detection
Input/Output System LSI servo sense input
Output Stepping control 1
Output Stepping control 2
– 41 –
MD-MT270H
Function