Subscribe to Our Youtube Channel
Related Manuals for Anova MG246
Summary of Contents for Anova MG246
- Page 1 Instructions and user manual MG246 MG252 Millasur, SL. Rúa Eduardo Pondal, nº 23 - Pol. Ind. Sigüeiro 15688 - Oroso - A Coruña 981 696465 www.millasur.com...
- Page 2 ANOVA wishes to congratulate you for choosing one of our products and guarantees the assistance and cooperation that has always distinguished our brand over time. This machine is designed to last for many years and to be very useful if used in accordance with the instructions contained in the user manual.
-
Page 3: Table Of Contents
CONTENTS 1. Contents of the box 2. Symbols on the machine 3. Safe operation 4. Chain and cutter bar installation 5. Fuel and chain oil 6. Operation 7. Cut with the chainsaw 8. Maintenance 9. Maintenance of the saw chain and guide bar 10. - Page 4 Attention ! Read these notes before starting to work with the machine and keep them with the machine. Read the instructions carefully. Familiarize yourself with the control elements to be able to use the device safely. Always keep these operating instructions with the chain saw.
- Page 5 deviate from the manual or the specified manufacturer. This can be caused by the following factors, before or during each use should be considered: - If the machine is used correctly - If the method of cutting the material and how it is processed correctly. - The state of the machine.
-
Page 6: Contents Of The Box
1 CONTENTS OF THE BOX 1. Motor unit 2. Sword guard 3. Guide bar 4. Cutting chain 5. Spark plug wrench Carburetor adjustment screwdriver... -
Page 7: Symbols On The Machine
2.SYMBOLS ON THE MACHINE Read, understand and follow all warnings. Warning! Kickback hazard. Be careful of the kickback of the chain saw and avoid contact with the tip of the bar. (3) Do not use the saw with one hand. (4) Always use the saw with both hands (5) You should wear ear, eye and head protection. - Page 8 (h). Shows the installation direction of the chain saw. Position: In front of the chain cover (I). Sound level of this equipment. MG246:113 dB (A) MG252: 114 dB (A) (J). Manual engine start. k) Decompression valve (if included) Press the button on the decompression valve to open it.
-
Page 9: Safe Operation
3.SAFE OPERATION ■ Before operating the product 1. Before using our products, please read this manual carefully to understand the correct use of your unit. 2. Never operate a chain saw when you are fatigued, ill or upset, or under the influence of medications that can cause drowsiness or if you are under the influence of alcohol or drugs. - Page 10 cutting wood. Keep bystanders and animals out of the work area. Children, pets, and bystanders must be a minimum of 30 feet (10m) away when starting or operating the chain saw. 4. Never start mowing until you have a clear work area, secure footing, and a planned retreat path from the falling tree.
- Page 11 SAFETY PRECAUTIONS FOR CHAINSAW USERS Bounce can occur when the nose or tip of the guide bar touches an object, or when the wood comes in and pinches the chain at the cut. Contact at the tip in some cases can cause quick reverse action, flipping the bar toward the operator.
- Page 12 4 INSTALLING THE CHAIN AND CUTTING SWORD The saw chain has very sharp edges. Wear protective gloves for your safety. Make sure the motor has stopped and is off before adjusting the bar and saw chain. The chainsaw box must contain the items shown below: Machine Saw chain Cutting sword...
- Page 13 IMPORTANT It is very important to maintain proper chain tension. Rapid wear on the guide bar or chain that comes off easily can be caused by improper tension. Especially when using a new chain, take good care of it, as it must expand when used for the first time.
-
Page 14: Operation
6 OPERATION TO START THE ENGINE ■ Cold start:A "cold" start of the engine means starting it after at least 10 minutes after it was shut down or after refueling. Unscrew the gas tank cap and oil cap completely, but do not remove them from the machine, just hang up. - Page 15 Hot start: To warm start the engine immediately after it has stopped, follow steps 1 - 2 - 3 - 4 - 6 - 7 - 10 - 11 of the above procedure, making sure that the primer bulb is activated only 2-3 times.
- Page 16 When adjusting, take the following prompts: Make sure to adjust the carburetor with the bar chain attached. H and L needles are adjusted by authorized persons. The authorized range within the turn number as shown below. Needle H –1/4 Needle L –1/4 2.
- Page 17 How to check the chain brake: Turn off the motor. Hold the chain saw horizontally, release your hand from the front handle, tap the tip of the guide bar to a stump or piece of wood, and confirm brake operation. The level of operation varies according to the size of the bar.
- Page 18 Kickback protector ■ This saw is also equipped with a chain brake that will stop the chain in the event of kickback if it works properly. You should check the chain brake operation before each use, running the saw at full speed for 1 or 2seconds and pushing the front hand guard forward.
- Page 19 Cut a supported log In area A in the image above, saw from the bottom one third and finish sawing from the top. In area B, saw down from the top one third and finish sawing from the bottom. Delimbing a felled tree First check in which direction the limb is bent.
-
Page 20: Maintenance
8. MAINTENANCE Before cleaning, inspecting, or repairing the unit, make sure the engine has stopped and is cool. Disconnect the spark plug to avoid accidental starting. Follow the instructions for performing regular maintenance, preoperative procedures, and Daily maintenance routines. Improper maintenance can cause serious damage to the machine. - Page 21 Periodic service points ■ Cylinder fins Dust clogging between the cylinder fins will cause the engine to overheat. Periodically check and clean the cylinder fins after removing the air filter and cylinder cover. When installing the cylinder cap, make sure the switch wires and grommets are properly in place.
-
Page 22: Maintenance Of The Saw Chain And Guide Bar
Cutting teeth sharpening standards: Chain ■ It is very important for a smooth and safe operation to always keep the chain sharp. Your cutting teeth need to be sharp when: • Sawdust becomes dusty. • You need additional force to cut. •... - Page 23 Top plate Lower File Depth gauge Inclination angle angle diameter standard angle(55°) Screw Screw Lateral rotation inclinatio angle Chain type 30° 10° 85° 0.025 " Depth gauge lime Guide bar • Reverse the bar occasionally to avoid partial and unbalanced wear of the chain and bar.
-
Page 24: Storage
"*". Inclination Guide bar Chain Hound Pinio Chain pitch Length Ref. Ref. MG246 MG252 Links [inches/ Oregon Oregon 0.325 " 16”/ 40cm 0.058 ”/1.5mm two1BPX06 168PXBK095 Oregon... -
Page 25: Warranty
11. DISPOSAL AND ENVIRONMENTAL PROTECTION Never pour waste chain lubricant or 2-stroke fuel mixture into the drain or sewer system or ground, but dispose of it in an appropriate, environmentally friendly manner, for example, at a special collection point or landfill. If your machine does not work at any time, in the future or you do not need it any longer, do not dispose of the device together with your household waste, but dispose of it in an environmentally friendly way. - Page 26 Readjust needle speed -Check for inferior quality oil Replace 3) The oil does not come out -Check the oil flow for any obstruction Clean Should the unit require additional overhaul service, consult an authorized ANOVA service facility in your area.
-
Page 27: Specifications
Cutter head: Anova Anova Sword Kind: Rolled with pinion Size: 18 " 18 " Cutting length: 45 cm 45cm Saw chain Kind: Anova 18 " Chain pitch: 8.255 mm (0.325 in) Caliber: 1.47mm (0.058in) Specifications are subject to change without notice. - Page 28 Machine name: CHAINSAW Model / os: MG246 Recognized and approved standard to which it conforms: Directive 2006/42 / EC Tested according to:...
- Page 29 DISTRIBUTION COMPANY MILLASUR, SL RUA EDUARDO PONDAL, Nº 23 PISIGÜEIRO 15688 OROSO - A CORUÑA SPAIN CE DECLARATION OF CONFORMITY In compliance with the different CE directives, it is hereby confirmed that, due to its design and construction, and according to the CE mark printed by the manufacturer on it, the machine identified in this document complies with the relevant and fundamental requirements in health and safety.
-
Page 30: Parts
16. PARTS...
Need help?
Do you have a question about the MG246 and is the answer not in the manual?
Questions and answers