FODSPORTS M1-S plus User Manual
  1. Manuals
  2. Brands
  3. FODSPORTS Manuals
  4. Headsets
  5. M1-S plus
  6. User manual

FODSPORTS M1-S plus User Manual

Helmet bluetooth intercom
Hide thumbs

Advertisement

Table of Contents

----··
.......
FODSPORTS
Focus on outdoor sports
IYII-SPLUS
HELMET BLUETOOTH INTERCOM
User Manual
0
Bluetooth·
FOCUS ON OUTDOOR SPORTS

Advertisement

Table of Contents
loading

Related Manuals for FODSPORTS M1-S plus

Summary of Contents for FODSPORTS M1-S plus

  • Page 1 ----·· ..FODSPORTS Focus on outdoor sports IYII-SPLUS HELMET BLUETOOTH INTERCOM User Manual Bluetooth· FOCUS ON OUTDOOR SPORTS...

  • Page 4: Package Include

    1.Package Include: 1x M1-S PLUS Speakers& Hard Tube Microphone 1x USB Cable 1xSoft Microphone 1x 2.5mm to 3.5mm Cable 1xUnit Base 1x Metal Clip □� 2x 3M Glue Velcro 4x Velcro 2x Eva rubber 1x User Manual...
  • Page 5 2.Charging: 2.1 The function button lights up red when charging, and the red light goes out after finishing(As shown below). Please charge before using for the first time. 2.2 Please use a qualified charger 5V/1A±0.5A. 2.3 Please keep charging at least once every 2 months If the product is not used for a long time.

  • Page 6: Speaker Installation

    3.lnstallation & Disassembly 3.1 Speaker Installation 2.Attach the Headphone with Velcro 3.Place Velcro on the right position 1.0pen the inner helmet lining on the hook to the loop (the short-line on the left side of the helmet, match ear position and attach the velcro loops.
  • Page 7 3.2 Fixed by clamp 1.Find and assemble the Unit base and metal clip. 2.Fix the base on the right position. 3.Assemble the M1 S-PLUS: Insert the snap of the 4.lnsert the microphone and earphone connection bottom of the host in to the groove of the base, press the line, installation complete.
  • Page 8 3.3 Disassembly of the Device 1. Pull out the headset plug. 2. Press the upper clamp buckle and move the device upward to remove it.

  • Page 9: Operation (Getting Started)

    Switch On: Long press Intercom button and Function button at the same time for 3 seconds.Voice message will also say" Welcome to FODSPORTS Bluetooth Communication System". Switch Off: Long press Intercom button and Function button at the same time for 3 seconds.Voice message will also say "Power off".

  • Page 10: Low Power Notification

    Power Detect & Notification Function M1-S PLUS has power detect function,when device is on,short press Volume+ and Volume- button at the same lime,recorded voice message will tell you: Power over 90% Power over 50% Power lower than 50% Low Power Notification When power lower than 20%, red light flash in the function button and voice message will remind "Power...

  • Page 11: Voice Command

    Volume- button once. input function automatically When your M1-S PLUS is paired up with cellphone.Short Press Volume+ button and Volume- button once , will automatically switch on the voice command function (only for iOS). *Cellphone must have voice command function.

  • Page 12: Music Sharing

    short press Function button . Pause: short press Volume+ button . Volume Up: short press Volume- button . Volume Down: short press Volume+ button twice. Play Previous: short press Volume- button twice. Play Next: Music Sharing Long press 3 seconds •q *Start Sharing Music For example: A share music with B...
  • Page 13 Pause music firstly, long press volume + button about 3 seconds,voice notice"Stop Sharing Music" *About Music Sharing > Music sharing function is used only between two M1-S plus devices. > When you start stop music sharing, the music needs to be in pause status.
  • Page 14 When device is on,press Function and Volume+ buttons at the same time for 5 Memory Clear: seconds.Then M1-S PLUS will clear the pairing memory with other devices.The red and blue lights flash at the same time, clearing memory completely. -12-...

  • Page 15: Device Pairing

    5.Device Pairing 5.1 Pairing Modes 5.1.1 Passive pairing mode Hold down for 3 seconds When device is on.long press Function button to enter Pairing Mode.red and blue lights flash quickly.voice notice" pairing ". Pairing mode for connection to Bluetooth devices such as mobile phones and Bluetooth GPS.

  • Page 16: Pairing With Cellphone

    5.2 (A)M1-S PLUS connect with (B)M1-S PLUS A M1-S PLUS is on active search mode(refer to 5.1.2), B M1S-PLUS is on passive search mode(refer to 5.1.1),A and B M1-S PLUS change from flashing red and blue lights alternately to function and intercom buttons flashing blue lights at the same time,connect successfully.
  • Page 17 "Device Connected". 5.4 Connect with two phones Step1 . Connect to the first phone(refer to 5.3) Step2 . Long press the Function button, M1-S PLUS on passive search mode, connect to the second phone(refer to 5.3) -15-...

  • Page 18: Wire Connecting

    Notice: M1-S PLUS can connect with two phones, but only support one phone for audio input. 5.5 Wire Connecting Radio Speed detector Music player Any device with 3.5mm connector can transmit voice signal lo M1-S PLUS. When device wire connected by 2.5mm to 3.5mm cable to M1-S PLUS,Complete the wired sound source input.
  • Page 19 You need lo purchase a cable if you need a wired connection for Walkie-talkie equipment. 6.Multi-device pairing connection 6.1 Occasions: Rider A connect with Passenger B for intercom. Then A connect with two bluetooth devices and one wired equipment and B connect with one bluetooth device(as shown below).
  • Page 20 Step 1 . A M1-S PLUS connect with B M1-S PLUS(refer to 5.2) Step 2. Short press one time A or B intercom button to disconnect intercom Step 3. A connect with 2 phones(refer to 5.4) Step 4. A use 2.5 mm to 3.5 mm AUX audio line to connect with one audio device Step 5.
  • Page 21 Active pairing mode Passive pairing mode (flash slowly) (flash quickly) Active pairing mode Passive pairing mode (flash slowly) (flash quickly) Step 1: Unit A is on active search mode(refer to 5.1.2), Unit B is on passive search mode(refer to 5.1.1 ), Unit A and Unit B change from flashing red and blue lights alternately to function button and intercom button flashing blue lights at the same time,connect successfully.Short press the intercom button of Unit B for one time, exit intercom state temporarily.
  • Page 22 Step 4: The intercom buttons and function buttons of Unit A ,B ,C and D flash blue light at the same time, the connection of group intercom successfully. *You can connect more M1-S PLUS by repeating the above methods. Notice: The first and the last one M 1 S-PLUS can connect with another 2 Bluetooth devices. The M1 S-PLUS in the middle connection position of the group can connect with an additional Bluetoolh device.
  • Page 23 6.2.2 Memory Connection Function M1-S PLUS will remember paired units.but after switch off and want to reconnect again.please follow the procedure: STEP1 .Switch off all 4 units(A,B,C,D) and all Bluetooth devices connected to the headset such as cellphone and GPS. (II will affect the pairing) STEP2.
  • Page 24 Step 1 • � Step2 Step 3 Step4 Step 1 :Switch on 4 M1 S-Plus of ABC and D. Step 2: Unit AB C and D are all on passive search mode by long pressing function buttons.4 Units are flash blue and red lights alternately, voice notice"pairing". -22-...

  • Page 25: Technical Specifications

    Step 3:Shorl press the function button of one M1-S PLUS for one time,4 units keep flashing blue and red light alternately. Step 4: Afler 15 seconds, Voice notice "Searching" of 4 units , the function buttons and intercom buttons flash blue lights at the same time, group intercom connection finish successfully.

  • Page 28: Warranty Card

    This device complies with part 15 of the FCC rules.Operation is subject lo the following two conditions (1) this device may not cause harmful interference.and (2) this device must accept any interference received,including interference that may cause undesired operation. This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Table of Contents