Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MPS EDS-C1
Summary of Contents for MPS EDS-C1
- Page 1 EDS-C1 User’s Manual Website: https://www.mpsenergy.com.tw/ Visit us:...
-
Page 2: Table Of Contents
Content Specification ........................3 Operation .......................... 4 2.1. How to power on HMI ....................4 2.2. How to power off ......................4 2.3. Main Screen information ....................4 2.3.1. Battery Indication...................... 5 2.3.2. Assist levels ....................... 5 2.3.3. Walk mode ........................ 5 2.3.4. -
Page 3: Specification
1. Specification Input Voltage 12 / 24 / 36 V Communication UART / CAN for controller Interface BLE for app Display OLED Power / + / - button Operating -20°C ~ 60°C Temperature IP65 Certifications ISO 13849-1 2015 certification... -
Page 4: Operation
2. Operation 2.1. How to power on HMI Long press “Power key” for 3 seconds to power on the HMI. After powering up the HMI, you will see the startup screen as the following figure. 2.2. How to power off During HMI at power on state, you can long press “power key”... -
Page 5: Battery Indication
2.3.1. Battery Indication You can check the battery icon to know the current battery capacity as the following figure. Battery 100% ~ 76% Battery 75% ~ 51% Battery 50% ~ 26% Battery 25% ~ 11% Battery 10% ~ 0% Battery connection is disconnected 2.3.2. -
Page 6: Headlight On/Off
Keep pressing the DOWN key to enter the Walk mode. The speed limit for Walk mode is 6km/h. Release the DOWN key to return back to the assist mode. 2.3.4. Headlight ON/OFF Long press the UP key for 1 second. Once the headlight icon is displayed on the screen, the headlight is ON. -
Page 7: Range (Remain Distance)
※ In this screen, user can long press the DOWN key for 2 seconds to reset the ODO value to 0. 2.3.6. Range (Remain Distance) Short press the Power key to switch the mileage mode, the Range (Remain Distance) screen is as following figure. -
Page 8: Bike Status Monitoring
2.3.7. Bike status monitoring These status icon show on screen can assist user to check the status of the E-bike. For status like: Speed is over Speed Limit Brake status Low battery voltage Temperature is above the limited value on the controller If any of these status happens, the controller shall stop the motor output immediately. -
Page 9: Controller Status Monitoring
Temperature is above the limited value on the controller 2.3.8. Controller status monitoring These status icon show on screen can assist user to check the status of the controller. If any of below status happens: OC (Over Current) OT (Over Temperature) OV (Over Voltage) UV (Under Voltage) SW Error... -
Page 10: Connection Problem
Over Voltage Under Voltage 2.4. Connection problem If there is any connection problem between the controller and the HMI, a timeout logo will be displayed. Please try to switch the HMI and battery off first, and check if the cables are well connected and then switch on HMI again. The UART grounded logo sometimes will be showed before timeout happened, it indicated the problem is caused by UART communication error. -
Page 11: Ble Connection
2.5. BLE connection When the APP establishes a BLE connection with the HMI, on HMI it shall display the BLE pin code screen as following figure. ※ In this screen, user can long press the UP and DOWN keys simultaneously for 2 seconds to reset the BLE pin code to the default code (0000).
Need help?
Do you have a question about the EDS-C1 and is the answer not in the manual?
Questions and answers