Table of Contents
Advertisement
Spacer
QUICK START GUIDE
Install top hinge and door:
Install slide spacers on opposite sidewalls:
1.
Take out 4 screws and remove the two brackets and
1.
Install hinge with longer straight edge aligned to
1. Rotate door 180
0
and lift the door on to the bottom
spacers from the sidewalls of the unit - leave the
outside edge of cabinet. Do not tighten.
hinge.
Remove door by tilting forward and lifting door off
5.
screws in the brackets and spacers to keep them
bottom hinge. Retain shoulder washers; they will be
together.
2. Install hinge that was used on the opposite side of
reused.
2.
Using 4 screws, install the spacers and brackets on
the unit
the opposite sidewalls - the open ends of the brackets
Remove three screws from hinge holes on the
6.
need to remain toward the front of the unit.
opposite side. Reinstall into holes where the hinge
3. Align edge of the hinge with the outer edge of the
Note: Be sure that the hinge side of the unit has
was removed. Take care not to scratch cabinet.
unit while inserting hinge pin into top of door.
the slide bracket with the thicker spacer.
4. Tighten three screws and replace hinge cover.
Non-hinge Side
Remove bottom hinge:
1. Remove bottom hinge from cabinet using 1/4" socket.
Align and adjust the door:
+
Align and adjust the door (see DOOR ALIGNMENT AND
Open end of bracket
ADJUSTMENT).
Hinge Side
Back of Unit
Install grille:
2.
Rotate door 180
and set on bottom hinge.
o
Install the grille.
3.
Align edge of the hinge with the outer edge of the
unit.
3.
Line up rack slide with slide brackets and push rack in
4.
Tighten three hinge screws using a Torx T-25
all the way. Pull rack outward all the way to make sure
2. Remove corresponding screws on opposite side of
screwdriver.
locks are engaged.
cabinet. On some models there may be a nut behind
one or both screws on either side.
5.
Replace hinge cover.
Install bottom hinge:
Align and adjust the door:
Align and adjust the door (see DOOR ALIGNMENT AND
ADJUSTMENT)
Install two or three screws, depending on model.
Install grille and hinge cover
Replace nuts if used.
USER GUIDE
General Installation
LEVELING INFORMATION
1.
Use a level to
confirm the unit is
Door Adjustments
level. Level should
Reinstall Grille
be placed along top
edge and side edge
as shown.
2.
If the unit is not level, adjust the legs on the corners of
the unit as necessary.
u-line.com
u-line.com
Back of Unit
+
Thicker end
of spacer
Open end of bracket
1
USER GUIDE
General Installation
LEVELING INFORMATION
General Installation
1.
Use a level to
1. Rotate door 180
and lift the door on to the bottom
0
confirm the unit is
LEVELING INFORMATION
hinge.
level. Level should
1.
be placed along top
Use a level to
2. Install hinge that was used on the opposite side of
edge and side edge
confirm the unit is
the unit
as shown.
level. Level should
be placed along top
3. Align edge of the hinge with the outer edge of the
edge and side edge
unit while inserting hinge pin into top of door.
as shown.
4. Tighten three screws and replace hinge cover.
2.
If the unit is not level, adjust the legs on the corners of
Align and adjust the door:
the unit as necessary.
Align and adjust the door (see DOOR ALIGNMENT AND
2.
If the unit is not level, adjust the legs on the corners of
ADJUSTMENT).
the unit as necessary.
Install grille:
Install the grille.
3.
Confirm the unit is level after each adjustment and
repeat the previous steps as needed.
INSTALLATION TIP
3.
Confirm the unit is level after each adjustment and
repeat the previous steps as needed.
If the room floor is higher than the floor in the cutout
opening, adjust the rear legs to achieve a total unit rear
INSTALLATION TIP
1⁄8
height of
" (3 mm) less than opening's rear height.
Shorten the unit height in the front by adjusting the front
If the room floor is higher than the floor in the cutout
legs. This allows the unit to be gently tipped into the
opening, adjust the rear legs to achieve a total unit rear
opening. Readjust the front legs to level the unit after it is
1⁄8
height of
" (3 mm) less than opening's rear height.
correctly positioned in the opening.
Shorten the unit height in the front by adjusting the front
INSTALLATION
legs. This allows the unit to be gently tipped into the
opening. Readjust the front legs to level the unit after it is
1.
Plug in the power/electrical cord.
correctly positioned in the opening.
2.
Gently push the unit into position. Be careful not
to entangle the cord or water and drain lines, if
applicable.
3.
Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit's top
surface should be approximately
the countertop.
4.
Install the anti-tip bracket.
General Installation
5.
Remove interior packing material and wipe out the
inside of the unit with a clean, water-dampened cloth.
10
General Installation
u-line.com
1
1
Turn to Adjust
Turn to Adjust
u-line.com
1⁄8
" (3 mm) below
Advertisement
Table of Contents
