Patterson 043-2047 Operation Manual

043-2047 Hygiene Handpiece
Caution before use
!
・The Patterson Hygiene Handpiece is intended for use by dental
professionals only.
・Read this Operation Manual carefully before using the handpiece. Be
sure to follow all the operating instructions, including all cautions and
warnings.
・Keep this Operation Manual for future reference.

1. Specifications

Back-end configuration
Nose configuration
Chuck configuration
Maximum speed
Note:
The maximum speed may vary slightly depending on the type of tubing
connected to the handpiece.

2. Installation/Removal of Handpiece onto/from Tubing Connector

Installation:
●
１. Make sure that the tubing connector is ISO standard 4-hole.
２. Align the air/water inlet ports at the handpiece back end with the
corresponding holes of the tubing connector.
３. Holding the swivel ring of the handpiece with fingers, tighten the
nut of the tubing connector by turning it clockwise.
Removal:
Holding the swivel ring, remove the handpiece from the
●
tubing connector by turning the nut counterclockwise.
Caution
!
・Never operate the handpiece if it rattles after connection to the tubing
connector or if any abnormality is sensed. In such a case, consult the
Patterson Service Center.
・Never attempt to forcibly connect the handpiece to the tubing
connector when the screw-in of the handpiece to the tubing connector is
too tight. Never use pliers or any other tools for the installation.

3. Installation/Removal of Prophy/Contra Angle or Bur (Attachment)

onto/from Handpiece
Removal of Bur Blank:
●
in the direction indicated by the black arrow until the chuck clicks open
and pull the bur blank out.
Installation of Prophy/Contra Angle:
●
１. Make sure that the chuck is open.
２. Insert the spindle into the chuck all the way until the back end of the
prophy/contra angle contacts the shoulder of the nose of the handpiece,
aligning the slit at the back end of the prophy/contra angle with the
protuberance of the nose of the handpiece.
３. Holding the motor, twist the nose in the direction indicated by the
white arrow until the chuck clicks shut.
４. Before operation, pull the attachment to make sure that it is securely
installed onto the handpiece.
Installation of Bur:
●
１. Make sure that the chuck is open.
２. Insert the bur spindle into the chuck all the way until the spindle
touches the back of the chuck.
３. Place the nose of the handpiece upward so that the bur inserted does
not slide down, then twist the nose in the direction indicated by the
white arrow until the chuck clicks shut.
４. Before operation, pull the attachment to make sure that it is securely
installed onto the handpiece.
Caution
!
・Never install a damaged attachment onto the handpiece such as a
worn-off bur, bur or prophy/contra angle with a bent spindle. Such
attachments may not only injure patients, but critically damage the
handpiece.
・Never install a non-ISO standard bur or prophy/contra angle with a
non-ISO standard spindle.
・Never open/close the chuck without installing the attachment onto the
handpiece, as the chuck holding power may be prematurely reduced.

4. Operation

Set the air pressure gauge for 2.0 kgf/㎠(28psi).
●
Before operation, be sure to make a trial run and make sure:
●
１. The drive-air is not leaking from the connecting part of the handpiece
back end and tubing connector.
２. Changes in the rotating direction and rotating speed can be manipulated
with the control ring as shown below:
*When the ring is turned in "F" direction, the attachment installed onto
the handpiece rotates clockwise.
*When the ring is turned in "R" direction, the attachment installed onto
the handpiece rotates counterclockwise.
*The rotation is stopped at the center position between "F" and "R".
Select the rotating direction and the speed by manipulating the ring
●
according to the treatment purposes.
Operation Manual
Applicable to ISO standard 4-hole connector
Applicable to U-type prophy/contra angles
Applicable to ISO standard 2.35 dia. spindle
5,500rpm at drive-air of 2.0 kgf/㎠(28psi)
6,000rpm at drive-air of 2.5 kgf/㎠(36psi)
Swivel Ring Swivel Ring
Holding the motor, twist the Bur Lock Ring
OM-MK038E 001