Panasonic WJ-HD500 Service Manual page 12

8 Set the Program Timer to PROG1 by pressing the
Increment/Decrement Buttons (+ or –) as shown in Fig. 3-8.
8
Press the Set Button (SET), and the PROG1 setting menu
as shown in Fig. 3-9 will appear on the monitor screen.
3-1 PROG1(WITHOUT AUDIO)
NO START END G1
1 0:00 24:00 M/S
RATE 7.5
2 -:-- -:-- M/S
RATE 10
3 -:-- -:-- M/S
RATE 5
4 -:-- -:-- O/S
RATE 15
SET TOTAL REC RATE ON EACH TABLE
G1+G2+G3+G4= UNDER 30FPS
Fig 3-9
8
Move the cursor to the START time editing area of NO.1
by the Direction Buttons (A, B, D or C).
8 Set the time to start the recording to 0:00 by the
Increment/Decrement Buttons (+ or –) as shown in Fig. 3-9.
8 Move the cursor to the END time editing area of NO.1 by
the Direction Buttons (A or B).
8
Set the time to end the recording to 24:00 by the
Increment/Decrement Buttons (+ or –) as shown in Fig 3-9.
8
Move the cursor to the Recording Mode editing area for
Group 2 (G2) by pressing the Direction Buttons (A or B).
8
Set the Recording Mode to – (disable) by pressing the
Increment/Decrement Buttons (+ or –) as shown in Fig. 3-9.
8 Set the Recording Mode of Group 3 (G3) and Group 4
(G4) to – (disable) by the same procedure as above.
8
Move the cursor to the Recording Mode editing area for
Group 1 (G1) by pressing the Direction Buttons (A or B).
8
Set the Recording Mode to M/S by pressing the
Increment/Decrement Buttons (+ or –) as shown in Fig. 3-9.
8
Press the Set Button (SET), and the M/S setting menu as
shown in Fig. 3-10 will appear on the monitor screen.
3-1-1-1 PROG1-NO1-G1 REC SETUP
M/S(EVENT RECORDER
REC MODE
REC RATE
QUALITY
PRE PICTURES
POST PICTURES
DYNAMIC REC
Fig 3-10
8
Move the cursor to the REC RATE in the menu by
pressing the Direction Buttons (D or C).
8
Set the Recording Rate to 15FPS by pressing the
Increment/Decrement Buttons (+ or –) as shown in Fig. 3-
10.
G2 G3 G4
- - -
7.5 1 10
- O/S O/S
5 1
M/S M/S M/S
2 2 5
M/S - M/S
10 10
MULTI SHOT)
15FPS
SUPER FINE
15
60
OFF
8 Move the cursor to the PRE PICTURES by pressing the
Direction Buttons (D or C).
8
Set the number of the pre-recording image to the value
other than 0 by pressing the Increment/Decrement
Buttons (+ or –) as shown in Fig. 3-10.
8
Press the Setup /Escape Button (SET UP/ESC) three
times to return to the WJ-HD500 SETUP menu as shown
in Fig. 3-5.
8 Move the cursor to ALARM SETUP by pressing the
Direction Buttons (D or C), then press the Set Button
(SET). The ALARM SETUP menu as shown in Fig. 3-11
will appear on the monitor screen.
6 ALARM SETUP
ALARM TERMINAL SETUP
AUTO RESET
ALARM OUTPUT
ALARM BUZZER
VIDEO LOSS
VIDEO MONITOR DETECTION
VMD AREA SETUP
ALARM MODE MULTI OUTPUT
8
Move the cursor to VIDEO LOSS by pressing the
Direction Buttons (D or C).
8
Select OFF by pressing the Increment/Decrement Buttons
(+ or –) as shown in Fig. 3-11.
8 Move the cursor to VIDEO MOTION DETECTION by
pressing the Direction Buttons (D or C).
8
Select OFF by pressing the Increment/Decrement Buttons
(+ or –) as shown in Fig. 3-11.
8
Press the Setup/Escape Button (SET UP/ESC) for two
seconds or more to close the setup menu and to return to
the normal screen.
8 Confirm that the Yellow LED of Numeric Button 1 only
lights up.
– 8 –
OFF
2S
2S
OFF
OFF
SPOT
SPOT OUTPUT SPOT
Fig 3-11