Table of Contents
Advertisement
Quick Links
Power Tool Brake
User Manual
Note: The image above represents one particular configuration of this product though this manual
can be used for all product configurations.
COPYRIGHT © 2021 BY MAKESAFE TOOLS, INC
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR
FORM WITHOUT THE WRITTEN APPROVAL OF MAKESAFE TOOLS, INC.
Advertisement
Table of Contents
Summary of Contents for MAKESafe Tools PTB-V120-P1
- Page 1 Note: The image above represents one particular configuration of this product though this manual can be used for all product configurations. COPYRIGHT © 2021 BY MAKESAFE TOOLS, INC WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF MAKESAFE TOOLS, INC.
- Page 2 DISCONNECT ALL SOURCES OF POWER PRIOR TO SERVICING THIS DEVICE. Important! Retain this manual and include it with the original user manual for the machine on which this device is installed. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 1...
-
Page 3: Table Of Contents
Identifying Motor Type Reverse-Threaded Spindles Limitations of Operation Recognizing Existing Controls How to Check for a Magnetic Switch. Installation Occupational Safety Standards Calibration Normal Operation Inspections & Maintenance Troubleshooting Service MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 2... -
Page 4: Introduction
2. Suitable for connection in the field to a branch circuit rated not more than 20 amperes and capable of delivering not more than 5,000 rms symmetrical amperes. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 3... -
Page 5: Device Diagrams
4.1” x 2.2” x 0.9” in. (105 mm x 57 mm x 23 mm) *All dimensions are for enclosure and do not include dimensions of buttons, plugs, and cable glands. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 4... -
Page 6: Compatibility Checklist
Confirm the power tool does not contain an integral Review your tool manual and inspect ❏ your tool to ensure there are no circuit breaker. integral circuit breakers. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 5... -
Page 7: Identifying Receptacles
(image below),or you see jointers, and disc sanders typically use sparking from your motor, your power AC Induction Motors. tool does not have an AC induction motor. (handheld power tools example) MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 6... -
Page 8: Reverse-Threaded Spindles
Power tools should never be operated wheel guards, blade guards, shields, without manufacturer-provided and OSHA and other manufacturer-provided and required guards. OSHA required guards are properly installed and adjusted. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 7... -
Page 9: Recognizing Existing Controls
MAKESafe Tools for assistance. Warning: Below are some examples of existing controls that would prevent a plug-and-play installation. If your machine has any of the following controls, please contact MAKESafe Tools before proceeding with your installation: Note: this is a list of examples but does not represent every possible control. If in doubt, contact MAKESafe Tools. -
Page 10: How To Check For A Magnetic Switch
It is likely that you have a magnetic switch or other type of control installed. Contact MAKESafe Tools before proceeding with your installation. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 9... -
Page 11: Installation
*It is the end user's responsibility to read and interpret all occupational safety requirements along with their local authority having jurisdiction. Interpretations provided here are the opinion of MAKESafe Tools. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 10... -
Page 12: Calibration
Never turn an adjustment more than 1/8 of a turn at any one time. 5. Repeat until you achieve the desired result. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 11... -
Page 13: Normal Operation
Be sure to replace the cover before plugging in the device. I don’t know what’s happening Please contact MAKESafe Tools at: and I need help. service@makesafetools.com or (415) 937-1808. MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 12... - Page 14 (this page intentionally blank) MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 13...
- Page 15 (this page intentionally blank) MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 14...
-
Page 16: Service
Service If you have any questions or your device needs service, please contact us. service@makesafetools.com (415) 937-1808 www.makesafetools.com MAKESafe Tools, Inc. | Copyright 2021 | Last Updated 12/29/21 Page 15...