Table of Contents
Advertisement
Quick Links
1 Description
The Electromagnetic Lock (Maglock) series is a surface-mounted,
magnetic-lock assembly. They are available in single- and dual-
lock varieties, various sizes (i.e. force), and also avaible with or
without built-in Door Status Switch ("DS" versions). All models
are designed for standard installation on most types of doors.
door configuration
10MAGLOCK1UL
10MAGLOCK1ULDS
10MAGLOCK5UL
10MAGLOCK5ULDS
2 Specifications
ATTENTION: This product must be powered from a UL-listed, regulated, power-limited, power supply!
DESCRIPTION
Lock:
Input Voltage:
Relay Rating:
Relay Power Factor:
Reed Switch Rating:
Reed Switch Power Factor:
Power Consumption:
Dimensions:
Certification:
Operating Temperature:
Operating Humidity:
NOTE: The specifications listed above are for an indoor, dry,
installation location.
75.5367.08 UL MAGLOCKS 1200lb 20210806
door status sensor
single
dual
with
10MAGLOCK1UL
10MAGLOCK1ULDS
single
12 or 24 VDC
1.0 A @ 24 VDC
resistive
1
dry contacts: 3W (switching contact 0.25 amps
max, switching voltage 30VDC max; resistive load)
1
500 mA @ 12 VDC /
250 mA @ 24 VDC
10.47 x 2.87 x 1.58 in
266 x 73 x 40 mm
UL1034, UL294
32 – 120 °F (0 – 49 °C)
0 – 85%
UL MAGLOCKS 1200LB
without
10MAGLOCK5UL
10MAGLOCK5ULDS
1.0 A @ 24 VDC
dry contacts: 3W (switching contact 0.25 amps
max, switching voltage 30VDC max; resistive load)
500 mA @ 12 VDC /
250 mA @ 24 VDC each
20.94 x 2.87 x 1.58 in
532 x 73 x 40 mm
32 – 120 °F (0 – 49 °C)
UL 294 Performance Ratings:
(required per Chapter 10 of 2015 IBC)
Destructive: Level I
Endurance: Level IV
Static Strength: 1000 lb
USER'S GUIDE
ELECTROMAGNETIC LOCKS
double
12 or 24 VDC
resistive
1
1
UL1034, UL294
0 – 85%
Line Security: Level I
Standby Power: Level I
Dynamic Strength:
Door Position
Switch
70 ft/lb
Page 1 of 5
Advertisement
Table of Contents
Related Manuals for BEA 10MAGLOCK1UL
Summary of Contents for BEA 10MAGLOCK1UL
- Page 1 Door Status Switch (“DS” versions). All models are designed for standard installation on most types of doors. Door Position Switch door configuration door status sensor single dual with without 10MAGLOCK1UL 10MAGLOCK1ULDS 10MAGLOCK5UL 10MAGLOCK5ULDS ...
- Page 2 3 Precautions Shut off all power going to header before attempting any wiring procedures. Maintain a clean and safe environment when working in public areas. Constantly be aware of pedestrian traffic around the door area. Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door. CAUTION Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires and cause damage to equipment or cable insulation.
- Page 3 6 Armature Plate Installation SIDE VIEW 1. hole for nut DOOR 2. hole for guide pin rubber washer 3. steel washer spacer DOOR 4. rubber washer 5. steel washer armature plate 6. armature plate 7. permanent magnet 8. guide pin screw (M8 35mm)* * Align the black, plastic piece of the armature plate with the cover plate (i.e.
- Page 4 7 Installation – Electrical (cont.) POWER The product must be powered from a UL-listed, regulated, power-limited, power supply. 12 VDC INPUT stallation - Mechanical & Electrical - Required power: 0.5 AMP / 12 VDC - Connect positive (+) lead from a 12 VDC power source to Terminal 1. - Connect negative (-) lead from a 12 VDC power source to Terminal 2.
- Page 5 BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS BEA Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA Inc. does not guarantee any use of the sensor/device outside its intended purpose.
Need help?
Do you have a question about the 10MAGLOCK1UL and is the answer not in the manual?
Questions and answers