Advertisement
Available languages
Available languages
3.3.- Mode B (B=Erase)
1.
Set the selector switch of the actuator to "B". The push button LED flashes
red.
2.
Actuate the push button of the actuator. The push button LED switches over
from red flash light to continuous light.
Note: There is 3 minutes timeout for the erasing link process, during this
time, LED is continuously red and waiting a sensor device to be deleted.
After that, the LED flashes red again.
3.
Set the transmitter sensor device into link configuration mode.
4.
After a successful deleting, the red LED starts to flash again. If deleting
process fails, the red LED continues lighting permanently.
5.
Returning to the operating mode: Set the operation mode switch of control
element and actuator to "F" or "Rpt." position.
6.
If a further transmitter should deleted from the same actuator, repeat the
described procedure above.
3.4.- Mode Rst. (Rst.=Erase all)
In the (Rst.) mode, all units programmed to the actuator can be completely
deleted. (Reset to factory conditions).
1.
Set the selector switch of the actuator to "Rst.". Push button LED flashes
red fast.
2.
Actuate the push button LED. After 3 sec. the LED switches over from fast
flashing (flickering) to permanent light. Press the push button LED
furthermore. After further 3 sec. the LED changes again to fast flashing
(flickering). Stop actuating the push button LED.
3.
All transmitters are deleted from the actuator.
4.
Returning to the normal operating mode. Set the operation mode switches
to "F".
4.- Operation
For operating, the configuration mode selector is selected in the following 2
possible
Mode F (F= Standard mode)
In F position, commands are transmitted to the actuators and trigger a
corresponding switching action.
If transmitters and actuators are trained as scene components, scenes can
be saved and started.
Mode Rpt. (Rpt.= Repeater mode)
The repeater mode position Rpt. is identical with the standard mode F plus
the activated repeater function.
In the repeater mode, the unit receives telegrams and re-transmits them with
maximum power. Before transmitting, the telegram is checked. Faulty
telegrams are not re-transmitted. Programming of transmitters is not
required. The repeater automatically repeats all telegrams whose telegram
structure is known.
Repeater function is only selected in that installations where it is found
communication difficulties between wireless devices.
The Repeater, when necessary, should be installed in a privileged position
at the installation, where it can provide coverage to most of the devices at
the installation. The best position it is usually the centre of the installation.
To activate Repeater function at a device, select Rpt. at the configuration
mode selector.
Important:
Select Repeater function to maximum 1 or 2 devices, only when necessary.
4.1.- Operation modes
Following operating modes: (a) switch and (b) time delayed switch off, can be
selected through the operation mode selector:
INT
3s,
5min, 10min
y 30min.
4.2.- Switch operation mode
Operation
Operation
Operation
Operation
selector
selector
selector
selector
Switch: INT
4.3.- Time delay switch operation mode
Selector
Selector
Selector
Selector
(defined time delay)
(defined time delay)
(defined time delay)
(defined time delay)
Time delay switch:
3s
1 min
5 min
10 min
30 min
5. Guarantee
This product is subject to the guarantee offered in the selling general terms of
ABB in each country.
positions:
Switch
1min,
Time delay switch with different delay
options: 3s, 1min, 5min, 10min y
30min.
mode
mode
mode
mode
Received
Received
Received
Received
wireless
wireless
Action
Action
Action
Action
wireless
wireless
telegram
telegram
telegram
telegram
Relay Output: Relay's contacts are closed
Switch_ON (1)
Push button LED: red continuous light
Relay Output: Relay's contacts are open
Switch_OFF (0)
Push button LED: green continuous light
Received
Received
Received
Received
wireless
wireless
wireless
wireless
Action
Action
Action
Action
telegram
telegram
telegram
telegram
Relay Output: Relay's contacts are closed.
Switch_ON
Time delay after is open.
Push button LED: When relay is closed it
lights continuous red. When relay opens, it
lights continuous green.
Relay Output: No action.
Switch_OFF
Push button LED: No LED change.
Advertisement
