Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Denver MET-110
Summary of Contents for Denver MET-110
- Page 1 MET-110 denver-electronics.com June 2021...
- Page 2 Safety information Please read the safety instructions carefully before using the product for the first time and keep the instructions for future reference. 1. This product is not a toy. Keep it out of the reach of children. 2. Keep product out of the reach of children and pets to avoid chewing and swallowing.
- Page 3 With your metal detector, you can hunt for coins, relics, jewelry, gold, and silver just about anywhere. This metal detector is versatile and easy to use. Features include: Two operating modes: All Metal and Disc. ALL METAL – Lets you search for different types of metals with automatic ground balance and high sensitivity.
-
Page 4: Assembling The Metal Detector
COMPONENTS Control box Search coil Adjustable shaft with cable Arm rest ASSEMBLING THE METAL DETECTOR Assembly is easy and requires no special tools. Just follow the steps below. 1. Unscrew the knobs on the search coil and remove the knobs and the connector. - Page 5 Lock nut 3. Insert the latch on top of the handle into the assembly hole at the bottom of the control box. Slightly push the control box in the direction of the “IN” marking on the handle to fix the latch in place.
-
Page 6: Adjusting The Search Coil
The search coil cable plug fits into the connector only one way. DO NOT insert the plug forcefully to avoid damaging it. DO NOT remove the shaft lock nut. Should you remove it, place the washer on top of the shaft connected to the handle with the small head of the washer pointing up. -
Page 7: Using Earphones
1. If the detector is switched on, turn the power switch (on the control box) to POWER OFF. 2. Press down the battery compartment cover and slide the cover off in the direction of the arrow. 3. Connect the batteries to the battery connectors observing the correct polarity. -
Page 8: Listening Safely
Connect a pair of headphones (not supplied) to the metal detector so you can listen to it privately. Using earphones also saves battery power and makes it easier to identify subtle changes in the sounds you hear, for better detection results. To connect headphones to the metal detector, insert the 3.5 mm plug into the EAR jack on the control box. -
Page 9: Functions And Indicators
• Do not listen at extremely high volume levels. Extended high-volume listening can lead to permanent hearing loss. • Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing. - Page 10 automatic ground balance. Rotate the control knob slowly clockwise to eliminate different trash objects. Rotate the control knob counter-clockwise towards the end to get to ALL METAL mode. The ALL METAL mode also comes with automatic ground balance. This mode used to find not only ferrous metals, but also non-ferrous metals (see more details below).
- Page 11 above the surface. Sweep the search coil from side to side in an arc line of 2.75 inches (7 cm) motion. When the metal detector detects a buried target, it sounds a tone. Make a visual note of exact spot on the ground where the detector beeps.
- Page 12 • Sweep slowly, as hurrying will make you miss targets. • Sweep the search coil from side to side in an arc line of 3 inches (7.5 cm) motion and keep it parallel to the ground. Factors that affect detection Accurate detection results are difficult to achieve.
- Page 13 Please notice - All products are subject to change without any notice. We take reservations for errors and omissions in the manual. ALL RIGHTS RESERVED, COPYRIGHT DENVER A/S Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to...
- Page 14 Additional information is available at the technical department of your city. DENVER A/S Omega 5A, Soeften DK-8382 Hinnerup Denmark...
Need help?
Do you have a question about the MET-110 and is the answer not in the manual?
Questions and answers