Subscribe to Our Youtube Channel
Summary of Contents for DEL CMP MCD-250SE-01
- Page 1 ® MCD SPA OZONE GENERATOR INSTALLATION INSTRUCTIONS & PRODUCT MANUAL MCD-250SE-01 C-M-P.COM/DEL 4-2602-01 Rev.D...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS When installing and using the DEL MCD Spa Ozone Generator, basic safety precautions should always be followed. Be sure all the electrical power is shut OFF at the main circuit breaker before installing the MCD. READ AND FOLLOW ALL INSTRUCTIONS.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION 1 Installation 1. How the DEL Spa Ozone Generator Works ......1 2. Installation Parts ................1 3. Installation Tools and Materials ..........1 4. Unit Assembly ................. 1 5. Mounting ..................1 6. Plumbing – Vacuum System ............1 7. -
Page 4: Section 1 Installation
SECTION 1 Installation 1. How the DEL Spa Ozone Generator Works DEL Generators produce ozone gas which is introduced to the spa water through suction. Tubing is used to connect the Ozone Generator to an injector or a vacuum port provided by the spa manufacturer. -
Page 5: Plumbing - Ozone Generator
SECTION 1 Installation 7. Plumbing – Ozone Generator (refer to Figure 1) a. Connect the PVC ozone tubing provided to the hose barb on the Ozone Generator. b. Slide hose clamps onto the tubing and run the tubing to the vacuum source. -
Page 6: Operation
SECTION 1 Installation 9. Operation a. With the spa filled to the proper level, run the spa controller through several cycles. b. Verify that the Ozone Generator turns on and off as required by the controller: LED light will illuminate when the ozone generator is turned on (cover must be removed to view light). -
Page 7: Section 2 Maintenance
SECTION 2 Maintenance For optimum performance, we recommend the MCD be replaced every five years. Ozone tubing and check valve should be replaced annually. Follow the steps below to replace the MCD and tubing. Refer to Figure 2. Condensate may collect in dips or loops in the tubing. If NOTICE condensation appears in the tubing, DO NOT DRAIN IT as the moisture may be moderately corrosive. - Page 8 OZONE GENERATOR COMPONENT LOCATIONS LED Light Mounting Screw Locations Ozone Generator (Cover removed for clarity) Power Supply Ozone Cell Cover Air Filter Ozone Outlet Figure 2: MCD Component Locations...
-
Page 9: Troubleshooting
TROUBLESHOOTING Problem Description Cause Remedy Green Algae 1. Green water 1. Low ozone, 1. Superchlorinate 2. Green spots on bromine or 2. Brush spa (removing surface chlorine levels algae) 3. Slippery surface 2. Low algaecide 3. Vacuum spa (removing levels algae) 4. -
Page 10: Replacement Parts
REPLACEMENT PARTS CMP P/N DESCRIPTION 2-0078 HOSE CLAMP (4 REQUIRED) 7-0075 OZONE TUBING (5 FT REQUIRED) 7-1140-01 CHECK VALVE... -
Page 11: Support
SUPPORT SAVE THESE INSTRUCTIONS Record Information on this System Below & Keep for Your Records Installer ______________________________________________________________ System Purchased From _____________________________________________ Installation Date _____________________________ Serial Number _______________________________ Model Number ______________________________ CMP Customer Service & Tech Support Toll Free: 1-800-733-9060 FAX: 770-632-7115 support@c-m-p.com Warranty Questions RMA@c-m-p.com... - Page 12 CMP , LLC 36 HERRING ROAD, NEWNAN, GA 30265 WWW.C-M-P .COM/DEL 0721AB...
Need help?
Do you have a question about the CMP MCD-250SE-01 and is the answer not in the manual?
Questions and answers