Advertisement
Table of Contents
50 AMP TRANSFER RELAY DELAY
The 50 Amp Transfer Relay connects the power from the shore cord or the generator to the coach's
distribution panel. Power from both these sources is fed into the box. The full power of these sources is
available within this box. Inadvertent shorts inside this box could result in severe damage and/or injury.
All servicing within this box should be done only by a qualified Service Technician.
Tools Required:
Accurate Voltmeter (
digital read-out preferred
Intellitec
www.intellitec.com
SERVICE MANUAL
Transfer Relay Delay 00-00803-400
Dual
Input
Genset
INDUSTRIAL CONTROL EQUIPMENT TYPE 1
Shore Power Rating: 120/240VAC 60HZ 1 Phase 50A/Pole
Generator Rating: 120/240VAC 60HZ 1 Phase 50A/Pole
CAUTION:
RISK OF ELECTRIC SHOCK, MORE THAN ONE DISCONNECT SWITCH MAY BE REQUIRED
TO DE-ENERGIZE THIS DEVICE FOR SERVICING.
ATTENTION:
RISQUE DE CHOC ELECTRIQUE. IL PEUT ETRE NECESSAIRE DE COUPLER
L'ALIMENTATION A PLUS D'UN INTERRUPTER POUR EFFECTUER LE DESAMORCAGE DE CE DISPOSTIF.
WARNING:
TWO SEPARATE POWER SOURCES. REFER SERVICE TO QUALIFIED PERSONNEL.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, INSTALL IN A CONTROLLED ENVIRONMENT
RELATIVELY FREE OF CONTAMINANTS.
FOR SUPPLY CONNECTIONS:
USE STRANDED CONDUCTORS,
COPPER,
RATED FOR 75ºC MIN
4-6 AWG
TORQUE 35 IN-LBS
GENSET
COACH PANEL
CHASSIS GROUND
SHORE POWER
Part Number 00-00803-400
CAUTION
).
1
-
DUAL INPUT GENSET
Intellitec
C
US
R
2N52
LISTED
TR50
P/N 53-00803-400 Rev. C 041519
1485 Jacobs Rd.
Deland, FL 32724
386.738.7307
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intellitec 00-00803-400
Summary of Contents for Intellitec 00-00803-400
- Page 1 50 AMP TRANSFER RELAY DELAY DUAL INPUT GENSET SERVICE MANUAL Transfer Relay Delay 00-00803-400 Intellitec Dual Input Genset INDUSTRIAL CONTROL EQUIPMENT TYPE 1 Shore Power Rating: 120/240VAC 60HZ 1 Phase 50A/Pole Generator Rating: 120/240VAC 60HZ 1 Phase 50A/Pole CAUTION: RISK OF ELECTRIC SHOCK, MORE THAN ONE DISCONNECT SWITCH MAY BE REQUIRED TO DE-ENERGIZE THIS DEVICE FOR SERVICING.
- Page 2 IMPORTANT! During installation, wire per the wiring diagram and instructions printed on the box cover. The field wiring screws must be tightened to 35 in-lbs to insure a tight connection. 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
- Page 3 FROM GENSET GENSET SHORE POWER SHORE POWER COACH PANEL COACH PANEL LINE1 NEUT LINE2 LINE1 NEUT LINE2 LINE1 NEUT LINE2 Cover removed (INSIDE VIEW) FIGURE 1 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
- Page 4 50 AMP TRANSFER RELAY DELAY DUAL INPUT GENSET SERVICE MANUAL RELAY DRIVE & DELAY ELECTRONICS Equivalent Circuit FIGURE 2 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
- Page 5 50 AMP TRANSFER RELAY DELAY DUAL INPUT GENSET SERVICE MANUAL RELAY DRIVE & DELAY ELECTRONICS FIGURE 3 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
- Page 6 50 AMP TRANSFER RELAY DELAY DUAL INPUT GENSET SERVICE MANUAL RELAY DRIVE & DELAY ELECTRONICS FIGURE 4 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
- Page 7 Transfer Relay terminals. Check the circuit breakers in the coach distribution box to be sure they are not tripped. Reset them to be sure. Replace Transfer relay. 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
- Page 8 50 AMP TRANSFER RELAY DELAY DUAL INPUT GENSET SERVICE MANUAL 1485 Jacobs Rd. Intellitec Deland, FL 32724 386.738.7307 www.intellitec.com P/N 53-00803-400 Rev. C 041519...
Need help?
Do you have a question about the 00-00803-400 and is the answer not in the manual?
Questions and answers