Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for uAvionix tailBeaconX STC
Summary of Contents for uAvionix tailBeaconX STC
- Page 1 tailBeaconX Installation Manual UAV-1003599-001 Rev A...
- Page 2 retained.
-
Page 3: Revision History
1 Revision History Revision Date Comments 2/3/2022 Initial release UAV-1003599-001 Rev A... -
Page 4: Warnings / Disclaimers
2 Warnings / Disclaimers All device operational procedures must be learned on the ground. uAvionix is not liable for damages arising from the use or misuse of this product. This equipment is classified by the United States Department of Commerce's Bureau of Industry and Security (BIS) as Export Control Classification Number (ECCN) 7A994. -
Page 5: Limited Warranty
For the duration of the warranty period, uAvionix, at its sole option, will repair or replace any product which fails in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. -
Page 6: Table Of Contents
7.4 Additional Required Equipment ................ 15 7.5 Mounting ......................16 7.5.1 Direct Mounting ..................16 7.5.2 Spacer Mounting ..................18 7.6 Wiring ....................... 19 7.6.1 uAvionix AV-30-C Wiring ................ 22 7.7 Unit Installation ....................23 7.8 Post Installation Checks ................... 25 UAV-1003599-001 Rev A... - Page 7 7.8.1 Ground Tests..................25 7.8.2 ADS-B Out Performance Test ..............25 System Configuration .................... 25 8.1 tailBeaconX Configuration ................25 8.1.1 Verify Software Version ................25 8.1.2 Configure Device ..................26 8.2 AV-30-C Configuration ..................26 Support ......................... 26 Appendix A AV-30-C Control Head .................
-
Page 8: System Information
Those installing this article on an aircraft listed on the Approved Models List shall verify the compatibility of existing STCs with the tailBeaconX STC prior to returning the aircraft to service. For installations on non-US registered aircraft, verify validity of the tailBeaconX STC for your Make and Model with relevant authorities or consult the uAvionix tailBeaconX webpage country specific information. -
Page 9: Tailbeaconx Universal Installation Kit
TCAS II or ACAS X. AV-30-C tailBeaconX STC Installation of a uAvionix AV-30-C by FAA STC SA00410BO is a prerequisite for this tailBeaconX STC. tailBeaconX is not operable without an installed AV-30-C. See appropriate AV-30-C STC Installation Manual (UAV-1003947-001) for AV-30-C installation instructions. -
Page 10: System Specifications
6 System Specifications 6.1 Wi-Fi Wi-Fi is intended only for on-ground configuration. Wi-Fi is only enabled in standby (STBY) mode and disabled when in ALT or ON mode. To restore Wi-Fi functionality after flight, the device must be set back to STBY mode. - Page 11 14V current 0.2A idle 0.25A typical 0.5A maximum 28V current 0.1A idle 0.125A typical 0.25A maximum Note: Shown with Universal Installation Kit UAV-1003793-001, including spacer UAV-1003599-001 Rev A...
-
Page 12: Wired Control Interface Specifications
6.5 Wired Control Interface Specifications Characteristics Specifications Physical RS-232 Rate and properties 2400 bps 8N1 Protocols UCP and UCP-HD Suppression Input 10 VDC minimum For more control interface details, see Appendix A. 6.6 Wireless Configuration Interface Specifications Characteristics Specifications Standard 802.11b/g/n Wi-Fi Access Point Security WPA2-PSK with unique key... -
Page 13: Installation
7 Installation 7.1 Unpacking and Inspecting Carefully unpack the device and make a visual inspection of the unit for evidence of any damage incurred during shipment. If the unit is damaged, notify the shipping company to file a claim for the damage. To justify your claim, save the original shipping container and all packing materials. -
Page 14: Tailbeaconx Universal Installation Kit Uav-1003793-001
7.2.1 tailBeaconX Universal Installation Kit UAV-1003793-001 The tailBeaconX Universal Installation Kit consists of the following parts: Item 1 Mounting Gasket, tailBeacon UAV-1001756-001 2 Mounting Plate, tailBeaconX UAV-1003125-001 3 Socket Head Cap Screw, M2 x 4, VT (2) UAV-1002820-003 4 Flat Head Phillips Screw, 4-40 x 1in (2) UAV-1002184-001 6 Dome Head Phillips Screw, #6 Coarse Thread (2) UAV-1003792-001 5 Flat Head Phillips Screw, 6-32 x 1in (2) -
Page 15: Installation Materials And Tools
The following table details what functions are provided directly by tailBeaconX. Transponder ADS-B Transponder Control Head Altitude Rear Transmitter Receiver Antenna Antenna Encoder Position Annunciation Light For the described installation configuration, the uAvionix AV-30-C provides control, display, annunciation, and pressure altitude information. UAV-1003599-001 Rev A... -
Page 16: Mounting
7.5 Mounting tailBeaconX is a rear, aft position light. Ensure that when mounted, the fin antennas and the top of the assembly are free from obstructions such as the rudder or vertical stabilizer. tailBeaconX requires a clear view of the sky for optimal GPS performance. - Page 17 7.5.1.1 Direct Mounting Dimensions Direct mounting plate UAV-1003125-001 shown. 7.5.1.2 Direct Mounting Procedure The mounting plate utilizes either the included #4-40 or #6-32 mounting hardware. The mounting plate can be installed with the screw pattern oriented either vertically or horizontally as shown above. Determine the orientation of the existing aft position light mounting hardware, and install the mounting plate accordingly.
-
Page 18: Spacer Mounting
Trimming the thru-hole maybe necessary for proper clearance and fitment. 4. Peel the backing from the Mounting Gasket and affix to the Mounting Plate. 5. Temporarily align the Mounting Plate to the opening, and ensure the depth of the cavity is sufficient to fully contain the tailBeaconX body. If not, follow the Spacer Mounting installation procedure in Section 7.5.2. -
Page 19: Wiring
engagement of the mounting hardware, considering the additional spacer thickness. Note: Installation of the tailBeaconX must be in accordance with AC 43.13- 2B, Chapter 1 and aircraft maintenance manuals. 7.6 Wiring In most cases, tailBeaconX will require less electrical power than the legacy light it is replacing. - Page 20 Gauge ohm/km Maximum Length for 0.5ohm 20 AWG 14.2m 22 AWG 7.8m 1. Prepare the aircraft wiring for connection. a. Install a shielded 24AWG twisted pair cable from the cockpit to the tailBeaconX installation location. This cable is used for interface control (data).
- Page 21 NOTE: Wires shown trimmed to an appropriate length 2. Connect the tailBeaconX red wire to the switched position light power wire using environmental splices or equivalent. 3. Connect the tailBeaconX black wire to the battery or airframe ground. 4. Connect the tailBeaconX orange and grey wires to the 2 twisted pair conductors connected to the control head or equivalent equipment.
-
Page 22: Uavionix Av-30-C Wiring
8. Route new wires away from coax, strobe wires, and other existing wires that might interfere. Secure wires so they do not touch or rub control surfaces or pulleys. 7.6.1 uAvionix AV-30-C Wiring Connect the RS-232 transmit and receive wires from the tailBeaconX to the AV-30-C, as shown below. -
Page 23: Unit Installation
7.7 Unit Installation The tailBeaconX unit must be electrically connected, then installed into the Mounting Plate by aligning the mounting tabs on the tailBeaconX with the cut-outs in the Mounting Plate. This requires you to rotate the unit 5º Counter-Clockwise from vertical before inserting. Once inserted gently, rotate Clockwise to vertical and secure with M2 anti-rotation screws. - Page 24 Ensure that the tailBeaconX is oriented consistent with the installation direction indication on the labels. This ensures the GPS antenna is correctly oriented skyward. 2. Secure the tailBeaconX to the Mounting Plate using the two supplied M2 anti-rotation screws and the included 1.5mm hex driver. Ensure threads are fully coated in thread locking compound before installation.
-
Page 25: Post Installation Checks
7.8 Post Installation Checks 7.8.1 Ground Tests Transponder testing can be conducted to verify Mode A/C/S and Extended Squitter operation. See tailBeaconX Instructions for Continued Airworthiness (UAV-1003600-001) for test procedures. 7.8.2 ADS-B Out Performance Test If the owner desires to further confirm the tailBeaconX was installed and configured properly, perform a flight within ADS-B airspace coverage and request a FAA flight test compliance report. -
Page 26: Configure Device
AV-30-C must be configured for tailBeaconX control. From the AV-30-C “Install” menu, configure “SERIAL 2” to “BEACON X”. See AV-30-C STC Installation Manual (UAV-1003947-001) for additional details on AV-30-C setup and configuration. 9 Support For additional questions or support please visit: https://www.uavionix.com/support/ UAV-1003599-001 Rev A... -
Page 27: Appendix Aav-30-C Control Head
Appendix A AV-30-C Control Head The AV-30-C is the control interface to the tailBeaconX. Pilot inputs shown below. Configured Callsign Current Squawk Code Transponder Mode (STBY, ON, ALT) GPS NIC (integrity metric) GPS NACp (accuracy metric) Pressure Altitude – Green indicates radar interrogation and will change to IDT if IDENT is active. -
Page 28: Appendix B Suppression Interface
Appendix B Suppression Interface tailBeaconX supports mutual suppression input only. tailBeaconX will suppress 1090Mhz Mode A/C/S and Extended Squitter transmissions when the suppression input is above 10VDC to eliminate interference with on- board electronics such as DME and TAS systems. UAV-1003599-001 Rev A...