Vermeer S725TX Operator's Manual
  1. Manuals
  2. Brands
  3. Vermeer Manuals
  4. Mini Skid Steers
  5. S725TX
  6. Operator's manual

Vermeer S725TX Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

S725
TX
Mini Skid Steer
Operator's
Manual
S725TX_o1_02
Serial No. 101 -
Order No. 105400DA8
Cabled Assembly Order No. 163724876

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S725TX and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Vermeer S725TX

Summary of Contents for Vermeer S725TX

  • Page 1 S725 Mini Skid Steer Operator’s Manual S725TX_o1_02 Serial No. 101 - Order No. 105400DA8 Cabled Assembly Order No. 163724876...
  • Page 2 This manual explains the proper operation of your machine. Study and understand these instructions thoroughly before operating or maintaining the machine. Failure to do so could result in personal injury or equipment damage. Consult your Vermeer dealer if you do not understand the instructions in this manual, or need additional information.
  • Page 3 Orientation: Right and left sides of the machine are determined by standing on the operator platform and facing forward. RADEMARK VERMEER, VERMEER Logo, EQUIPPED TO DO MORE are trademarks of Vermeer Manufacturing Company. KUBOTA is a trademark of Kubota, Ltd., Osaka, Japan.
  • Page 4 Vermeer Industrial Equipment not excluded below shall be repaired or replaced at Vermeer’s option without charge by any authorized independent Vermeer dealer. The warranty repair or replacement must be made by a Vermeer independent authorized dealer at the dealer’s location. Vermeer will pay for replacement parts and such authorized dealer’s labor in accordance with Vermeer’s labor reimbursement policy.
  • Page 5 (7) Transportation costs, if any, of transporting to the Vermeer dealer. Freight costs, if any, of transporting replacement parts to the Vermeer dealer. (8) The travel time of the Vermeer dealer’s service personnel to make a repair on the retail purchaser’s site or other location. (9) In no event shall Vermeer’s liability exceed the purchase price of the product, (10) Vermeer shall not be liable to any person under any circumstances for any incidental or consequential damages (including but not limited to, loss of profits, out of service time) occurring for any reason at any time.
  • Page 6 (12) Depreciation damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow operating instructions, misuse, lack of proper protection during storage. (13) Accessory systems and electronics not of Vermeer’s manufacture are warranted only to the extent of such manufacturer’s respective Limited Warranty if any.
  • Page 7 NO DEALER WARRANTY. The selling dealer makes no warranty of its own and the dealer has no authority to make any representation or promise on behalf of Vermeer or to modify the terms or limitations of this warranty in any way.
  • Page 8 This page intentionally left blank.
  • Page 9 ___ Check that loader arms do not lower with key in OFF position and lift lever pushed. ___ Check forward and reverse ground drive operation. ___ Check that park brake functions. ___ Check track tension. S725TX Mini Skid Steer Receiving and Delivery Report i...

  • Page 10: Attachments

    Bucket attachment instructions are contained in this S725 Operator’s Manual. Contact your authorized Vermeer dealer, or visit www.vermeer.com for information on attachments authorized for use by Vermeer Corporation. ELIVERY Check and perform the following with the customer: ___ Review all sections of the Operator’s Manual.

  • Page 11: Dealer/Owner Information

    NFORMATION dealer owner address address city city state / province state / province zip / postal code zip / postal code country country phone number phone number email address email address S725TX Mini Skid Steer Receiving and Delivery Report iii...

  • Page 12: Identification Numbers - Record

    DENTIFICATION UMBERS ECORD Machine Model Number ___________________________ Machine Serial Number ___________________________ Engine Model Number _________________________ Engine Serial Number _________________________ iv Receiving and Delivery Report S725TX Mini Skid Steer...

  • Page 13: Machine Identification Decal

    ACHINE DENTIFICATION ECAL This decal provides easy identification of the model and 17-digit identification number. The barcode contains the machine’s VIN number and can be scanned with any barcode reading device. S725TX Mini Skid Steer Receiving and Delivery Report v...
  • Page 14 This page intentionally left blank.

  • Page 15: Table Of Contents

    Cold Weather Starting ......22-2 S725TX Mini Skid Steer Table of Contents vii...
  • Page 16 Electricity ........40-5 Operating with Other Vermeer-Authorized Attachments . . .50-11 Gas .

  • Page 17: Safety Messages

    Indicates a hazardous situation that, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. NOTICE Indicates information considered important, but not hazard-related. S725TX Mini Skid Steer Safety Messages 10-1...

  • Page 18: Safety Symbol Explanation

    WARNING: Read Operator’s Manual and safety signs, and watch the operations and safety video, before operating machine. WARNING: Check machine before operating. Machine must be in good operating condition and all safety equipment installed and functioning properly. 10-2 Safety Messages S725TX Mini Skid Steer...
  • Page 19 WARNING: Failure to use Shutdown Procedure can result in unexpected hazard(s). Death or serious injury could result due to entanglement, crushing, cutting, or other hazardous contact. Follow Shutdown Procedure after operating, before performing any service or maintenance, and before transporting. Follow Shutdown Procedure, page 23-1. S725TX Mini Skid Steer Safety Messages 10-3...
  • Page 20 Wait for leaking to stop before disconnecting the fitting. Fluid injected under the skin must be removed immediately by a surgeon familiar with this type of injury. 10-4 Safety Messages S725TX Mini Skid Steer...
  • Page 21 WARNING: Moving parts can crush. Keep hands, feet, and clothing away from power-driven parts. Keep shields in place and properly secured. WARNING: Hot fluid under pressure can scald. Allow engine to cool before opening radiator cap. S725TX Mini Skid Steer Safety Messages 10-5...

  • Page 22: Crystalline Silica

    Depending upon air monitoring results, the following measures may be necessary to avoid exposure to excessive levels of crystalline silica dust: • Perform an Exposure Assessment. • Create a Written Exposure Control Plan. • Housekeeping • Medical surveillance • Employee training 10-6 Safety Messages S725TX Mini Skid Steer...
  • Page 23 WARNING: Failure to follow any of the preceding safety instructions or those that follow within this manual, could result in death or serious injury. This machine is to be used only for those purposes for which it was intended as explained in this Operator’s Manual. S725TX Mini Skid Steer Safety Messages 10-7...
  • Page 24 This page intentionally left blank.

  • Page 25: Intended Use

    Section 15: Intended Use The S725TX Mini Skid Steer can be equipped with a variety of attachments for light and medium duty work. Contact your Vermeer dealer, or visit www.vermeer.com, for information on the list of authorized attachments. The S725TX must not be used with attachments which have not been evaluated by Vermeer Corporation and authorized for use.
  • Page 26 This page intentionally left blank.

  • Page 27: Controls

    Push forward ......increase engine speed Pull back......decrease engine speed S725TX Mini Skid Steer Controls 20-1...
  • Page 28 10–15 seconds. Continue to hold while cranking engine. Release button once engine starts. (4) 12V DC Auxiliary Electrical Outlet 12V available in Key ACC and Key RUN positions. (5) Hourmeter Indicates total number of hours engine has been in operation. 20-2 Controls S725TX Mini Skid Steer...

  • Page 29: Indicator Lights

    Light monitors engine oil pressure and comes on when the Keyswitch is initially turned ON. If the light does not shut off within 30 seconds after starting the engine or comes on during normal operation, shut off the engine and correct the issue S725TX Mini Skid Steer Controls 20-3...

  • Page 30: Control Station

    Back left ..front turns left when moving in reverse Back right ..front turns right when moving in reverse 20-4 Controls S725TX Mini Skid Steer...
  • Page 31 Center......... OFF Back .....oil flows through male coupler S725TX Mini Skid Steer Controls 20-5...
  • Page 32 Center .........OFF Back ......oil flows through male coupler 20-6 Controls S725TX Mini Skid Steer...
  • Page 33 Center ......... OFF Back ....oil flows through male coupler S725TX Mini Skid Steer Controls 20-7...
  • Page 34 Left ....... . . tilt attachment back 20-8 Controls S725TX Mini Skid Steer...

  • Page 35: Operator Presence System

    OFF before ground drive and attachment drive can be re-engaged. The Operator Presence system is intended for your safety and must be maintained in good functional condition. Contact your Vermeer dealer if it does not function correctly. RAKE A spring-applied, hydraulic-released park brake engages the left track when the engine is OFF or the operator leaves the platform with the engine on.

  • Page 36: Fuses And Relays

    (5) 15A Auxiliary Override (6) Open Not Used (7) 30A Spare (8) 15A Spare (9) Open Not Used (10) Open Not Used Relay Location Function Operator Presence Operator Presence Latch Neutral Start Fuel Shutdown 20-10 Controls S725TX Mini Skid Steer...

  • Page 37: Starting Procedure

    Check to see that engine temperature/oil pressure warning light goes off. If not, shut off engine and correct issue. Step 9: Warm up engine at medium speed. Do not operate the engine under load until engine has warmed up. S725TX Mini Skid Steer Starting Procedure 22-1...

  • Page 38: Cold Weather Starting

    (-15°C), remove battery from machine and store indoors until next machine use. NOTICE: Do not use ether starting aid. Ether may cause engine damage and void engine warranty. An electric block heater is available from your Vermeer Dealer. Hydraulic Fluid Allow adequate time for hydraulic oil to warm up, especially in cold weather.

  • Page 39: Battery Explosion - Avoid

    External: Flush with plenty of water. If eyes have been exposed flush with water for 15 minutes and get prompt medical attention. Internal: Drink large quantities of water or milk, follow with milk of magnesia, beaten egg, or vegetable oil. Call a physician immediately. S725TX Mini Skid Steer Starting Procedure 22-3...

  • Page 40: Jump-Starting Procedure

    (3). Start engine. Step 4: Step 5: Remove cables in REVERSE order and install covers over cable clamps. Close and latch engine access door. Discharged BLACK Machine frame Boost battery 22-4 Starting Procedure S725TX Mini Skid Steer...

  • Page 41: Shutdown Procedure

    NOTICE: Park brake will engage when operator steps off platform or engine is shut off and spring-applied park brake pin is aligned between sprocket teeth. The brake will engage within 4˝ (10 cm) of travel. S725TX Mini Skid Steer Shutdown Procedure 23-1...
  • Page 42 This page intentionally left blank.

  • Page 43: Transporting The Machine

    Place trailer on a level surface and block wheels or engage park brake of the towing vehicle. • Do not load if trailer bed or ramps are slippery. • Excessive ramp angle may increase difficulty in loading/unloading. S725TX Mini Skid Steer Transporting the Machine 30-1...

  • Page 44: Loading/Unloading

    To help avoid sudden stops, keep both feet fully on the platform and stand as far to the rear as practical. Slow down when traveling over uneven ground. 30-2 Transporting the Machine S725TX Mini Skid Steer...

  • Page 45: Driving Onto Trailer

    Stop machine when tie-down position is reached. Tie-down position distributes machine weight on the trailer as recommended by the trailer manufacturer. Step 8: Lower lift arms and adjust tilt until attachment is firmly on trailer deck. Step 9: Shut off engine and remove key. S725TX Mini Skid Steer Transporting the Machine 30-3...
  • Page 46 WARNING: Attachments could slip off the trailer after being disconnected from the machine, resulting in a crushing injury. When disconnecting and backing the machine away from the side of a trailer, take precautions to assure the attachments are properly secured to the trailer. 30-4 Transporting the Machine S725TX Mini Skid Steer...

  • Page 47: Driving Off Trailer

    Slowly move machine down the ramp to the ground. Minimize steering while on the ramps. Steering while on the ramps may result in the machine driving off the ramps or cause the ramps to move and drop off the trailer deck. S725TX Mini Skid Steer Transporting the Machine 30-5...

  • Page 48: Loading With Crane

    ACHINE Attach a suitable towing chain Step 1: to front tie-down point (1) or rear tie-down points (2) to retrieve the machine in the event that the machine becomes mired or disabled. 30-6 Transporting the Machine S725TX Mini Skid Steer...
  • Page 49 Proper chocking of tracks is critical to keep machine stationary until ready to tow. The park brake is located on left side of machine. S725TX Mini Skid Steer Transporting the Machine 30-7...
  • Page 50 “Park Brake - Check” in the Maintenance Manual instructions. Tighten bypass valves prior to returning unit to service. Torque bypass Step 10: valves to 15–18 ft-lb (20–24.5 Nm). 30-8 Transporting the Machine S725TX Mini Skid Steer...

  • Page 51: Clean Machine

    Keep pressure washer stream away from machine controls and electrical/electronic devices. Compressed air can also push moisture through some connector and component seals. Do not point air nozzle directly at seal areas. S725TX Mini Skid Steer Transporting the Machine 30-9...
  • Page 52 This page intentionally left blank.

  • Page 53: Preparation

    Become familiar with the controls, operation and use of the machine under the supervision of a trained and experienced operator. The operator must be familiar with the workplace’s safety rules and regulations, and must be mentally and physically capable of operating the machine safely. S725TX Mini Skid Steer Preparation 40-1...

  • Page 54: Personal Protection

    Eye protection must consist of wraparound safety glasses or goggles. Other workers in the immediate area must also wear hard hats, safety shoes, hearing protection, and eye protection. 40-2 Preparation S725TX Mini Skid Steer...

  • Page 55: Sound Levels

    Hand/arm vibration exposure has been measured according to ISO 5349. The level is below 2.5 m/s REPARE THE WARNING: Keep all spectators and other workers away from the machine and work area while in operation. S725TX Mini Skid Steer Preparation 40-3...

  • Page 56: Locate Buried Utilities

    If utility cannot be precisely located, it must be shut off by the utility company. 40-4 Preparation S725TX Mini Skid Steer...

  • Page 57: Look For Evidence Of Underground Placement

    Do not allow anyone to approach the machine. Some circuit breakers automatically reset. Do not assume power has been permanently disconnected until you confirm that the utility company has locked out power to that line. S725TX Mini Skid Steer Preparation 40-5...

  • Page 58: Gas

    Death or serious injury could result. Keep well away from cliff edges. Do not dig under the machine or attachment. Take care when backfilling. Do not go too close to edges. Do not drive or operate on unstable ground. 40-6 Preparation S725TX Mini Skid Steer...
  • Page 59 Do not operate this machine in an area with flammable dust or vapors. Carbon monoxide fumes from the engine can asphyxiate. Operate only outdoors or provide adequate ventilation if indoor operation is essential. S725TX Mini Skid Steer Preparation 40-7...

  • Page 60: Prepare The Machine

    TTACHMENTS WARNING: Using attachments authorized by Vermeer Corporation is important for your safety. Using unauthorized attachments may cause difficulties with steering, stopping, stability and other undesirable performance or handling characteristics, or they may not attach securely to your machine. Never use unauthorized attachments.

  • Page 61: Install/Remove

    Ensure pins are rotated so that tops of pins face outward as shown (1). Step 3: Start machine, and lower lift arm. Tilt loader mounting plate forward slightly. Step 4: Drive machine FORWARD, aligning loader mounting plate with attachment. S725TX Mini Skid Steer Preparation 40-9...
  • Page 62 Tops of pins must face inward as shown (3). NOTICE: Ensure pin ends extend through and are visible beneath attachment mount. Step 9: If attachment requires hydraulic power. Refer to “Hydraulics - Attach/ Detach,” page 40-12. 40-10 Preparation S725TX Mini Skid Steer...

  • Page 63: Attachment - Remove

    WARNING: Attachments could slip off the trailer after being disconnected from the machine, resulting in a crushing injury. When disconnecting and backing the machine away from the side of a trailer, take precautions to assure the attachments are properly secured to the trailer. S725TX Mini Skid Steer Preparation 40-11...

  • Page 64: Hydraulics - Attach/Detach

    WARNING: Hydraulic couplers, hoses, and fluid may be hot. Contact with hot parts may result in burns. Wear gloves when connecting and disconnecting hydraulic hoses, and wait until unit has cooled before touching hydraulic components. NOTICE: Ensure all foreign matter is cleaned from hydraulic connectors before making connections. 40-12 Preparation S725TX Mini Skid Steer...

  • Page 65: Hydraulics - Attach

    Auxiliary Attachment Levers are in NEUTRAL. Shut off engine. Step 2: Move Auxiliary Attachment Drive Lever forward, backward, and back to NEUTRAL position to relieve hydraulic pressure. Step 3: Unhook hoses from auxiliary hydraulic couplers. Remove attachment from machine. S725TX Mini Skid Steer Preparation 40-13...

  • Page 66: Auxiliary Low Flow (Option)

    Auxiliary Low Flow (Option) Machine may be equipped with optional auxiliary connections (2). 40-14 Preparation S725TX Mini Skid Steer...

  • Page 67: Operating The Machine

    Section 50: Operating the Machine APACITIES The S725TX has a rated operating capacity of 750 lb (340 kg) when tested in accordance with SAE J2752 and ISO 14397-1 standards NOTICE: Ensure weight of attachment plus materials being handled does not exceed the machine’s operating capacity.

  • Page 68: While Driving

    Move Ground Drive Joystick slowly to start moving the machine smoothly. Avoid sudden stopping, starting, or turning unless necessary. WARNING: Rider may fall out and be injured or killed. Do not carry riders. 50-2 Operating the Machine S725TX Mini Skid Steer...
  • Page 69 Sudden stops from higher travel speeds could throw you from machine, or the machine could tip over. To help avoid sudden stops, keep both feet fully on the platform and stand as far to the rear as practical. Slow down when traveling over uneven ground. S725TX Mini Skid Steer Operating the Machine 50-3...

  • Page 70: Safe Operating On Slopes

    Always travel with load lowered when traveling up or down slopes. You may also need to keep heavy end uphill for added stability. Do not exceed rated load capacity. Load on firm and level ground. Do not step off platform with load raised. 50-4 Operating the Machine S725TX Mini Skid Steer...
  • Page 71 Service brake retarding force - equal to traction of both tracks • Secondary brake - equal to traction of one track • Park brake holding force - equal to traction of both tracks S725TX Mini Skid Steer Operating the Machine 50-5...

  • Page 72: Operating The Mini Skid Steer

    The Operator Presence system in the operator platform detects the presence of an operator. The operator must be standing on the platform for the ground drive, lift/tilt functions, or auxiliary attachment drive to be engaged. Keep both feet on the platform. 50-6 Operating the Machine S725TX Mini Skid Steer...

  • Page 73: Bucket Operation

    40-8. Safety Precautions WARNING: Never work under an attachment unless it is adequately supported to prevent it from falling unexpectedly. WARNING: Falling load can crush. Keep load level when raising lift arms. S725TX Mini Skid Steer Operating the Machine 50-7...

  • Page 74: Moving Machine With Load

    Tilt bucket forward until cutting edge of bucket contacts the ground, and bottom of bucket is level with the ground. Step 3: Move machine forward slowly into the material while gradually tilting bucket backward as it fills. Step 4: Move machine backward away from the material. 50-8 Operating the Machine S725TX Mini Skid Steer...

  • Page 75: Digging With The Bucket

    Step 5: Continue driving machine forward until bucket is full. If ground is hard, tilt bucket forward and backward while driving slowly forward. When bucket is full, tilt bucket fully backward. Step 6: S725TX Mini Skid Steer Operating the Machine 50-9...

  • Page 76: Emptying The Bucket

    Step 3: Move machine in reverse to level loose material. Before moving forward, raise loader arms or tilt bucket back to lift the bucket cutting edge off the Step 4: ground. 50-10 Operating the Machine S725TX Mini Skid Steer...

  • Page 77: Backfilling With The Bucket

    THER ERMEER UTHORIZED TTACHMENTS Refer to the attachment manual supplied by the attachment manufacturer for operating and maintenance instructions for the attachment and additional instructions that may be required for the S725 S725TX Mini Skid Steer Operating the Machine 50-11...
  • Page 78 This page intentionally left blank.

  • Page 79: Maintenance Intervals

    23-1. Visually inspect machine daily before starting the machine. Make no modifications to your equipment unless specifically recommended by Vermeer Corporation. AFETY AINTENANCE Safety signs located on your machine contain important and useful information that will help you operate your equipment safely.

  • Page 80: Lift Arm Support Bar - Install/Remove

    Install support bar over lift arm cylinder as shown in right photo. Secure with pins in two outer holes (3). When work is finished, return Step 3: support bar to stow location. Install pins in two inner holes. 60-2 Maintenance Intervals S725TX Mini Skid Steer...

  • Page 81: Hourmeter - Check For Maintenance Interval

    The hourmeter is used to determine maintenance intervals for the machine. The hourmeter indicates the total number of hours the engine has been in operation. Maintenance intervals are based on normal operating conditions. When operating under severe conditions, the maintenance intervals should be shortened. S725TX Mini Skid Steer Maintenance Intervals 60-3...

  • Page 82: Maintenance Interval Schedule

    = Initial maintenance on new machine. Regular maintenance interval may be different. Initial = Regular maintenance interval. For Vermeer maintenance replacement part numbers, refer to the Parts Manual or call your Vermeer dealer. Each maintenance interval is also the title of chapter following this schedule. Refer to the appropriate chapter for instructions.
  • Page 83 Engine System - Check  Lift Arm Cylinders - Adjust  Air Cleaner Element - Replace  Battery - Replace  Track Tension - Adjust  Handgrip Bar - Adjust  Storage Procedure S725TX Mini Skid Steer Maintenance Intervals 60-5...

  • Page 84: Attachment Maintenance

    TTACHMENT AINTENANCE Refer to the attachment manuals provided by the attachment manufacturer. The attachment manuals must be attached to the machine together with the S725 Operator’s Manual. 60-6 Maintenance Intervals S725TX Mini Skid Steer...
  • Page 85 Hourmeter - Check for Maintenance Interval, 60-3 Controls, 20-1 Hydraulic Fluid, 22-2 Crystalline Silica, 10-5 Hydraulics - Attach, 40-13 Hydraulics - Attach/Detach, 40-12 Hydraulics - Detach, 40-13 Dealer Prep, i Dealer/Owner Information, iii Identification Numbers - Record, iv S725TX Mini Skid Steer Index...
  • Page 86 Indicator Lights, 20-3 Operating the Mini Skid Steer, 50-6 Install/Remove, 40-9 Operating with Other Vermeer-Authorized Attachments, 50-11 Intended Use, 15-1 Operator Presence System, 20-9 Operator Qualifications, 40-1 Jobsite Assessment, 40-6 Jump-Starting Procedure, 22-4 Park Brake, 20-9 Jump-Starting, 22-2 Personal Protection, 40-2...
  • Page 87 Trailer Preparations, 30-1 Trailer Selection, 30-1 Transporting the Machine, 30-1 Vibration Levels, 40-3 While Driving, 50-2 S725TX Mini Skid Steer Index...
  • Page 88 This page intentionally left blank.
  • Page 89 Updated control logo for gas engines. Removed engine fault codes, no controller. Introduction, warranty, warning icons, safety messages, Intended Use, keyswitch, o1_02 12/18 Front, 10, 15, 40, 50, Back issue/symptom, operating capacity, Proposition 65 added to FM file S725TX Mini Skid Steer Revision History...
  • Page 90 State of California to cause cancer reproductive harm. and reproductive harm. Wash hands after handling. Copyright 2014, 2016, 2018. All rights reserved. Vermeer Corporation 1210 Vermeer Road East, P.O. Box 200 Pella, Iowa 50219-0200...

Table of Contents

Save PDF