Summary of Contents for Pivot A20A
- Page 1 USER GUIDE PIVOT For iPad Pro 11-inch (1st, 2nd, and 3rd gen.) / iPad Air (4th gen.) [ Issued 11.15.2021 Version R02 ] Better Connection. Better Protection.
-
Page 2: Read Before Use
NOTE: Your PIVOT case will hold your device firmly on all sides in order to protect it from accelerated impacts and other hazards. Once installed, your device is not intended to be easily removed. -
Page 3: Device Compatibility
PIVOT A20A DEVICE INSTALLATION Device Compatibility The PIVOT A20A is compatible with multiple generations of iPad. Before attempting to install your iPad, refer to the information below to confirm compatibility. The PIVOT A20A supports the following devices: Supported Devices: Did You Know? iPad Pro 11-inch (3rd gen.) -
Page 4: Installing Device
Installing Device Align the device camera and buttons with the corresponding access points in the case body and press the corners of the device into the case beginning with the camera and button area. The device will snap securely into the case’s perimeter seal. Pro Tip! If the cases does not snap easily onto the device, double check the alignment... - Page 5 Installing The Screen Cover To install the PIVOT Screen Cover, position the case and cover in landscape orientation, with the volume and power buttons of the device in the upper left corner, as illustrated above with the device screen facing you.
- Page 6 Installing The Screen Cover Once the PIVOT Screen Cover and case body are properly aligned, with the corresponding access points in the case body and cover aligned with the buttons of the device, press the corners of the Screen Cover down onto the case body. The Screen Cover engages with the case body to hold firmly in place by gripping the three locations illustrated above, as follows: 1.
- Page 7 Locate the Center Finger Tab and lift gently. Apply Pro Tip! constant force while lifting to disengage the two Once open, adjust the angle of the PIVOT Snap-Closures, which are located to the left and Kickstand evenly on both sides to prevent right of the Center Finger Tab.
-
Page 8: Adjusting Viewing Angle
Adjusting Viewing Angle Adjust the viewing angle of the PIVOT Kickstand by rotating the left and right Legs of the kickstand evenly to the desired position. The PIVOT Kickstand Hinges provide a preset resistance force, which supports a range of viewing angles up to 120-degrees. -
Page 9: Label Area
The I.D. Label Area is located on the case back behind the Kickstand. Recommended Label Template: Avery 5167. Closing Kickstand To close the PIVOT Kickstand, rotate it from any open angle until it is nearly in the closed position, or at a 0-degree angle, parallel to the case body. -
Page 10: Incorrect Use
Incorrect Use The PIVOT Kickstand is durable if used as intended. However, it can be damaged if misused and put under repeated stress. Do not attempt to force the PIVOT Kickstand beyond maximum 120-degrees of rotation or adjust the Legs independently. Doing so may result in damage to the Kickstand, hinges, and case body. - Page 11 Screen Cover. Pencil Grip The Apple Pencil and similarly sized styluses snap firmly into the PIVOT Pencil Grip for secure storage when correctly installed in the orientation illustrated. The Pencil Tip Cradle* helps prevent accidental release of the Apple Pencil.
-
Page 12: Accessory Slots
PIVOT ACCESSORY SLOTS Accessory Slots This PIVOT case is compatible with select PIVOT accessories, such as the PIVOT Hand Strap. The Accessory Slots are located to the left and right of the clip with removable rubber inserts. Refer to the accessory product instructions for information on installation and removal of accessories. - Page 13 “CLICK.” 3. Depress the PIVOT Clip and reverse the process above to disconnect the case from the mount.
- Page 14 Incorrect Mount Alignment Shown below is an example of an incorrect alignment of the mounting plate and PIVOT case. The clip is not properly engaged with the mounting plate and is not holding the case in the locked position. The mounting plate is not fully inserted into the mounting channel and will not support the weight of the case and device.
-
Page 15: Getting Started
Getting Started Before beginning any clip replacement Flex procedure, please ensure you have a Spring compatible Pivot Clip Kit. This PIVOT case uses the PCK-2 Assembly, Gen 2.0. It Pivot Clip is not compatible with older versions of the PIVOT clip. - Page 16 Removing Hinge and Clip c) With one hand, hold the clip firmly against the case, apply even pressure to the clip. d) Using pliers with other hand, pull the hinge pin out. (Be careful, the clip is under spring tension.) e) Remove clip while holding the spring in place.
- Page 17 TECH SPECS (For Reference Only) Orthographic Views: Interior View:...
-
Page 18: Additional Information
Thank you. Additional Information To learn more about your PIVOT case, please visit pivotcase.com for instructional videos, product support and additional information about PIVOT products. You’ll find valuable online resources provided to enhance your user experience and see the complete line of PIVOT products.