Related Manuals for SachsenRad SachsenRad E-Racing R6
Summary of Contents for SachsenRad SachsenRad E-Racing R6
- Page 1 User Manual with E-Bike pass and maintenance log SachsenRad E-Racing Bike R6 Productnummer: BB12062 / BB12083...
-
Page 2: Table Of Contents
Inhalt VIDEO INSTRUCTIONS E-BIKE ID / BIKE PASS UNPACKING AND ASSEMBLY INSTRUCTIONS ASSEMBLY Before assembly Required tools Installing the front wheel Fitting the handle bar Aligning the steering head bearing and stem Installing the pedals Fitting the saddle Adjusting the saddle height 2.8. - Page 3 Thank you for purchasing our product! Please read these instructions carefully. Cycling is a natural part of a modern, health-conscious lifestyle. People are travelling longer and longer and the roads for riding are more complicated. Due to the physical differences, riding habits and handling characteristics of each cyclist, especially when riding uphill or long distances, cycling can be very strenuous.
-
Page 4: Video Instructions
VIDEO INSTRUCTIONS Under the following link you will find video instructions for assembly on YouTube https://www.youtube.com/watch?v=Y1pG6k6E--Y In case of a return, please contact our customer service first. In the case of a return shipment, please ensure that it is dismantled properly. We also have a short video online for you: https://www.youtube.com/watch?v=zJ2FOVUJSYw Under the following link you will find a video tutorial on how to adjust the brake system https://youtu.be/Tcc8BmI8occ... -
Page 5: E-Bike Id / Bike Pass
E-BIKE ID / BIKE PASS PLEASE COMPLETE THE FOLLOWING E-BIKE PASSPORT, IN MINIMAL FORM, CAREFULLY IN YOUR OWN INTEREST! FRAME NO.* MODEL TYPE ELECTRIC BIKE BATTERY SERIAL NO. ENGINE (REAR/CENTER) MOTOR SERIAL NO. (IF AVAILABLE) SIZE (IN INCHES) COLOR FRAME/FORK/RIM GEAR SHIFT DERAILLEUR TYPE/NUMBER OF GEARS... -
Page 6: Unpacking And Assembly Instructions
UNPACKING AND ASSEMBLY INSTRUCTIONS Tip: Your e-bike is slightly heavier than a normal bike. It is best if two people lift it out of the box. Required tools and aids (recommendation) - Tool kit (supplied, see 2.2) - Blanket or old carpet (to prevent the floor or the e-bike from being scratched during assembly. Please read the following instructions carefully before unpacking and assembling your e-bike and follow the recommended sequence. -
Page 7: Assembly
Designation of the e-bike parts Saddle Seat post Quick release saddle Rear brake Front wheel / tyre front brake pedals and chainring suspension fork battery slides drive chain rear wheel / tyre sprocket cassette motor battery charging connection bicycle handle bar left hand brake lever (rear brake control) right brake lever (front brake control) ASSEMBLY... -
Page 8: Required Tools
Required tools Supplied in the tool kit: Allen key 4s, 5s, 6s (3x) Open-end spanners 8/10, 13/15, 14/17 (3x) Screw driver NOT INCLUDED IN DELIVERY: Air pump with car valve Please bring the tyre pressure of the front and rear wheel to at least 2.8 bar with the help of an air pump BEFORE THE FIRST RIDE. -
Page 9: Fitting The Handle Bar
When everything is set correctly, slide the spring back onto the axle and carefully screw the grip nut onto your front axle until the quick release can be flipped over hand-tight, thus holding the wheel firmly in the mount. Now let the wheel turn by hand and check that it sits and runs correctly. Check and test the front brake. The ins- tructions for adjusting the brakes can be found under section 2.5. -
Page 10: Aligning The Steering Head Bearing And Stem
Aligning the steering head bearing and stem Note: This step may differ for your model and may not be necessary because it has already been pre-assembled. Note: In the photos above, the handlebars have not yet been fitted; this is for the sake of clarity. Please follow the described assembly sequence. -
Page 11: Fitting The Saddle
4. Use a 15 mm open-ended spanner to lock the foot. WARNING: Improper installation of the pedal can pose a serious safety hazard resulting in signifi-cant property damage, serious injury or death. Please check that the pedals are secure before each use. Fitting the saddle Make sure that the quick-release of the seat post is open (picture A). -
Page 12: Adjusting The Saddle Height
Adjusting the saddle height 1. The height of the saddle can be adjusted with the quick-release on the saddle rail. You only need to release the quick-release lever to freely select the height of the saddle. After you have adjusted the desired height, lock the quick-release lever again and the adjustment is complete. -
Page 13: Inserting The Battery
Front light If you do not find your front light already adjusted to the front of the bike, unpack the light from the accessory box and install it using the hexagonal bolt and nut supplied. You will find the neces-sary tools in the tool bag in the accessory box. -
Page 14: Breaking With The E-Bike
NOTE: Please keep the battery main switch in the 0 position until you are safely on the bike. WARNING: Do not sit on your bike with the bike stand unfolded as this may cause damage to the vehicle and personal injury. Nothing working? Please refer to section 9 for troubleshooting: F.A.Q. - Page 15 Functions of the control display • Battery indicator • Support levels • Speed display (incl. current speed, maximum speed and minimum speed) • Motor output display • Ride time • Distance and total distance • Assistant function • Switch lighting on/off •...
- Page 16 The status is displayed for 2 seconds and automatically returns to the current display. Operation and functions Assistant mode To activate the function, press and hold the - button. After 2 seconds, the e-bike continues to trav-el at walking speed (6 km/h). The function is switched off as soon as the - button is no longer pressed. This mode only works by keeping the - button pressed.
- Page 17 Reset default settings dEF Meaning: Default settings are restored. Press and hold the + key and the ON/OFF key for 2 seconds to enter the restore. Use the + and - keys to choose between YES and NO. If YES is selected, the restoration of the de- fault settings will be activated.
-
Page 18: Your E-Bike Battery
Error code definition 21 Technical fault 22 Throttle malfunction (connecting cable) 23 Engine problem 24 Transmission problem 25 Brake malfunction 30 Electro-communication fault 31 MOSFET tube short circuit 32 On/off button problem 33 +/- button problem 34 Voltage failure YOUR E-BIKE BATTERY Main switch of your e-bike battery. -
Page 19: Battery Use, Safe Storage And Handling
The motor and battery control stops automatically to protect the battery and prevent a power failure as soon as the battery voltage is below a certain value. Warning: Never use the battery until it is completely empty as this will seriously affect the capacity and charge level of the battery. -
Page 20: Factors Influencing Range
NOTE: Please use your charger indoors as damage caused by improper use is not covered by the warranty. Recharge plan (recommendations) Charging Hours First three charges Normal charging Every ten charges Charge the battery after each use to ensure the longest possible life. CAUTION: Never charge for more than 12 hours to avoid overcharging. -
Page 21: Before Your First Ride
BEFORE YOUR FIRST RIDE This section is to prepare you for your first ride. Please always wear a safety helmet of the correct size. If you wish to lend the e-bike to others, please ensure that they wear a safe and appropriate helmet. Do not take anyone with you on the bike! Overloading, which can be caused by double occupancy, can have serious consequences resulting in significant property damage, serious injury or death. -
Page 22: Maintenance
MAINTENANCE Component First Assembly 500km or after half 1000km or 1 each 1000km a year* year* Tubes and tyres Wheel incl. rims and spokes Brakes Lights and reflectors Stem and handlebars Steering head bearing Saddle (support) Frame Gear shift Suspension fork Battery and battery slide Drive system... -
Page 23: Wheels
the ground. If there are noises, there may be loose parts. Check that the lights can be used normally. If you have purchased a folding bike, please assemble it carefully before riding. Notes on inspection and maintenance of some components and sys-tems Wheels The front and rear wheels of the vehicle should be in the center of the fork or frame. -
Page 24: Brake System
Brake system Depending on the conditions, the braking effect may decrease after a short running-in period, or a squealig may be heard. The squeaking could be caused by contamination. You should clean your brake discs carefully with a suitable cleaner (brake cleaner). If the braking effect decreases, you can retighten the Bowden cables using the adjusting screws on your spective brake lever of the e-bike handlebar. - Page 25 1. Inspection 2.Inspection 3. Inspection 4. Inspection Carried out on: Carried out on: Carried out on: Carried out on: Signature/ Stamp Signature/ Stamp Signature/ Stamp Signature/ Stamp Specialist workshop Specialist workshop Specialist workshop Specialist workshop 1. Inspection 2.Inspection 3. Inspection 4.
-
Page 26: Frequently Asked Questions
F.A.Q. - Frequently asked questions about problems and their solutions Below are some common problems and solutions. If the following methods do not solve your prob-lem, please contact your dealer. Problem Possible cause Possible solution Control display does not 1. battery main switch inactive 1. - Page 27 Battery charge indicator 1. main switch of the battery is 1. set battery main switch to I not set to I 2. charge battery completely does not react (on the 2. battery empty 3. replace battery* battery) 3. battery defective Front light does not work 1.
-
Page 28: Data Sheet
Machinery Directive -2006/42/EC, Low Voltage Directive 2014/35/EU Product Safety 2001/95/EC, RoHS 2011/65/EU and Dir. Electromagnetic Compatibility -2014/30/EU. Please find the complete declaration here: www.leicke.de -> Fahrräder -> SachsenRAD R6 Angewandte technische Normen: DIN EN 15194 Fahrräder-Elektrisch unterstützte Fahrräder, DIN EN ISO 4210 DISPOSAL Our obligation to inform you according to the battery law. -
Page 29: Imprint
You are legally obligated to return used batteries/rechargeable batteries/lamps as the end user. In the case of a removable battery/accumulator or illuminant, you must return them separately to the appropriate return system. You can return used devices/batteries/lamps to the collection points of the public waste disposal authorities (recycling centers) and to distributors as defined by the ElektroG (retail trade). - Page 30 Warranty on battery: 1.We provide a 12-month guarantee on the proper functioning of the battery. The warranty starts from the date of purchase. The warranty service is limited to the repair or replacement of the bat-tery and is carried out at the discretion of LEICKE.
- Page 31 9. Warranty provisions other than those listed above are only valid if confirmed in writing by LEICKE GmbH / SachsenRad. 10. Should a technical problem occur with the e-bike you have purchased, please contact the sup-port hotline of LEICKE GmbH / SachsenRad. Contact: LEICKE GmbH, Stöhrerstraße 17,...
- Page 32 notes...
-
Page 33: 15. Return Receipt
City Leipzig 04347 City code Country Germany Ref. Return SachsenRad Country E-mail bought at bought on E-bike model / item number Frame size Color Please fill out this form carefully. All information is voluntary. Incomplete completion will not negatively affect your consumer rights, but will complicate and delay the processing of your return. - Page 34 In the case of signs of use or damage, as well as improper shipping, we may be entitled to charge the resulting depreciation. Please refer to the instructions in your dealer‘s cancellation policy. Defect Description Battery Charger Display (error code) Brakes Motor Handlebar...
- Page 35 notes...
- Page 36 We wish you a good trip with your SachsenRad E-Racing Bike R6.