Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BIAX MB 50
Summary of Contents for BIAX MB 50
- Page 1 Translation of the original operating manual Drive unit for flexible shafts MB 50 This manual must be provided to the user (operator)! BIAX Schmid und Wezel GmbH Maybachstrasse 2 D – 75433 Maulbronn Tel.: 07043 / 102-0 Fax: 07043 / 102-78 E-mail: biax-verkauf@biax.de...
-
Page 2: Technical Data
Translation of the original operating manual Drive unit for flexible shafts – MB 50 1 Technical Data Product name Drive unit for flexible shafts Type MB 50 Order number 010 402 280 Power consumption 3.1 kW Power output 2.8 kW 900 –... -
Page 3: Intended Use
You must make sure that only BIAX products are connected to the drive unit. The drive unit must not be operated in rooms with explosive or combustible gases, or gases hazardous to health. Any use of the drive unit for flexible shafts beyond the area of application stipulated, or constructional modifications to it, are not permitted without prior agreement from Schmid &... - Page 4 Translation of the original operating manual Drive unit for flexible shafts – MB 50 1) Workplace safety a) Keep your work area clean and well lit. Untidy or badly lit work areas can lead to accidents. b) Do not work with the power tool in a potentially explosive environment containing flammable liquids, gases or dust.
-
Page 5: Machine-Related Safety Instructions
Translation of the original operating manual Drive unit for flexible shafts – MB 50 power tool is impaired. Have damaged parts repaired before using the power tool. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges jam less and are easier to guide. -
Page 6: Handling The Machine
Translation of the original operating manual Drive unit for flexible shafts – MB 50 Loose connections, damaged, partially melted and melted through cables should be replaced immediately. Do not clamp or squeeze the cables. Lay cables in such a way that they do not cause tripping hazards and they cannot be damaged. - Page 7 Translation of the original operating manual Drive unit for flexible shafts – MB 50 When using carbide burrs and brushes, avoid exceeding the permissible load and circumferential speed in order to avoid danger to persons or damage to property. Complete a 30-second test run before starting to use the unit.
- Page 8 Mounting the Operating Unit on the Machine DANGER – Electricity! Do not open the cover of the MB 50 drive unit. Danger due to damage and contamination of electrical components Remove the 4 screws (A) from the drive unit as shown in Figure 1.
- Page 9 Translation of the original operating manual Drive unit for flexible shafts – MB 50 The operating unit with sheet (1) is fixed on the drive unit (5) at 4 points. For this purpose, the spacers (4) are positioned between the drive unit and the sheet of the operating unit as shown in Figure 2; then they are secured with the cylinder screws (2) and washers (3) included in the scope of delivery.
- Page 10 The rubber buffers on the stand feet ensure secure standing on a smooth surface. You can get either a moveable frame or a bench stand for the MB 50. 6.2.1 Mounting the Machine on the Bench Stand or Portable Stand Figure 4: Mounting on bench stand or portable stand ...
- Page 11 Translation of the original operating manual Drive unit for flexible shafts – MB 50 6.3 Mains Connection of the Machine DANGER – Electricity! Before use, check the ratings of the power supply network match those of the machine. WARNING – Rotating parts! Only connect the plug to the power supply after the system is ready for operation and the tool has been clamped in.
-
Page 12: Switching On And Off
Translation of the original operating manual Drive unit for flexible shafts – MB 50 Block the drive unit motor spindle (4) with the retention pin through the hole (5) in the motor flange (6). Using the retention pin (2), turn the shaft coupling (1) up to the stop on the motor spindle. -
Page 13: Speed Control
Translation of the original operating manual Drive unit for flexible shafts – MB 50 Now the workpiece can be processed. Work carefully in the area of corners, sharp edges, cracks, etc. Prevent insert tools from bouncing off the workpiece and jamming! Switching off ... -
Page 14: List Of Faults
Translation of the original operating manual Drive unit for flexible shafts – MB 50 Only use undamaged tools: Before each use, check the insert tools for splintering, cracks, wear or heavy abrasion. After falling down, check the machine and the tool for damage. -
Page 15: Flexible Shaft
Translation of the original operating manual Drive unit for flexible shafts – MB 50 Shaft break Disconnect unit from mains and replace flexible shaft, check the speed if necessary Motor overload The motor switches itself off for self-protection Shaft break... -
Page 16: Scope Of Delivery
Translation of the original operating manual Drive unit for flexible shafts – MB 50 10 Repairs WARNING – Unqualified personnel! Repairs are only allowed to be carried out by specialist personnel! Our Service department is available to you for this.
Need help?
Do you have a question about the MB 50 and is the answer not in the manual?
Questions and answers