Gardena 4030 Operator's Manual page 9

Ending active watering prematurely:
You can exit active watering (programmed or
started manually) prematurely without changing
the programs.
1. [ Fig. O7 ]: Press the Man. key.
and the channel flash.
SELECT CHANNEL SELECT CHANNEL
2. [ Fig. O20 ]: Select the active channel desired
(in the frame e. g. channel 4) using the ▲-▼ keys
and confirm by pressing the OK key.
Watering is ended and the main level is dis-
played.
Water all channels manually:
If all the channels are to be enabled manually, the
channels are opened manually one after the other
with the manual watering duration.
1. [ Fig. O22 ]: Press and hold down the OK key.
2. [ Fig. O23 ]: Also press and hold down the
Man. key for 3 seconds.
Run Time Man.,
MANUAL ALL MANUAL ALL
in the display.
3. [ Fig. O21 ]: Select the manual watering duration
( minutes are preset) using the ▲-▼ keys
00:30 00:30
(e. g. ) and confirm by pressing the OK key.
00:15 00:15
Manual watering starts with channel 1,
and the frame around the active
MANUAL ALL MANUAL ALL
channel flashes.
If the watering duration is not confirmed within
10 seconds by pressing the OK key, the watering
begins with the watering duration displayed.
You can exit watering all the channels prematurely
by pressing the OK key + Man. key for 3 seconds.
Percentage Watering Duration
(% Run Time Key)
You can end the programming mode at any time by
pressing the % Run Time key.
% Run-time-function:
The programmed watering durations of all the
watering programs can be changed centrally in
10 % increments from 10 % to 200 %, without
having to change the individual programs (e. g. if
you wish to water your garden less in the autumn
than in the summer).
ATTENTION! If the run time % figures are above
100 %, programs may overlap as a result
(see Setting the watering programs).
1. [ Fig. O24 ]: Press the % Run Time key.
and the percentage watering duration
RUN TIME % RUN TIME %
flash.
18
2. [ Fig. O25 ]: Select the figure for the percentage
E. g. in case of 60 % Run Time, a programmed
watering duration of 60 min. is reduced to 36 min.
Note:
When the percentage of the watering duration is
changed the display of the originally programmed
watering durations in the programs stays as it is.
When setting up / modifying a program, this is
automatically set to
TIME TIME
Watering Breaks (Rain Off Key)
You can end the programming mode at any time by
pressing the Rain Off key.
Rain Off function:
and minutes flash
If watering is not necessary, e.g. due to lengthy
rainfall, a watering break can be set. All the pro-
grams can be set for a 1 to 9-day break ( 1 to
case manual watering is still possible.
1. [ Fig. O26 ]: Press the Rain Off key.
2. [ Fig. O27 ]: Using the ▲-▼ keys, set the desired
3. [ Fig. O28 ]: Confirm the break by pressing the
From 2 days onwards, the remaining break period
displayed in hours (
(1 hour)).
To deselect the Rain Off function the Rain Off key
has to be pressed.
Key lock [ Fig. O29 ]:
The keypad can be locked to protect against
unintentional changing of the settings.
1. Press and hold down the OK key.
2. Also press and hold down the Rain Off key for
To disable the key lock, the OK key + Rain Off key
have to be pressed and held down for 3 seconds.
watering duration using the ▲-▼ keys (e. g.
) and confirm by pressing the OK key.
TIME 60 % TIME 60 %
The percentage watering duration has been
transferred and the main level is displayed.
100 % RUN TIME 100 % RUN TIME
does not apply to manual watering.
9 ) or they can all be blocked ( Off ), in which
and Off is displayed.
RAIN OFF RAIN OFF
break (e. g. 3 days 3 ).
Day Delay and the frame flash.
OK key.
The selected break (e.g. 3 days
displayed and the programs are suspended for
the break selected.
48H OFF 48H OFF
3 seconds.
The lock symbol is displayed.
RUN RUN
. The
% RUN % RUN
) is
3 DAYS OFF 3 DAYS OFF
(48 hours) ...
1H OFF 1H OFF