Table of Contents
Advertisement
Quick Links
Safety Module Combination KB55S/SS-EB75GS
Safety Module lk
Progressive safety gear - upward/downward acting = payload + weight of lift car in FREE fall
Braking device = 1/2 payload + masses UPWARDS upon tripping the overspeed governor incl. UCM/A3
Normal position drawn
General instructions
Mounting/adjustment
Mounting/adjustment/check
Mounting/information
Check
Test instructions/information
Schlosser
Aufzugtechnologie GmbH
Felix-Wankel-Straße 4
85221 Dachau
T +49 8131 / 5186-0
www.schlosser.de
Operating Instructions
EU-SG 374/EU-SG 735 / EU-SG 289
Tension shoe
Brake shoe
Brake pads
Brake shoe
Release slider
Ausgabe
Seiten
edition
pages
06.09.2018
1/7
General
Releasing bolt
Spring steel strip, inside
Lockwash
Douple eccentric
Kingpin, can be pulled out
Brake shoe retainer
Bearbeiter
person in charge
Kepplinger
drawn: safety gear right
left mirrored
Kingpin, can be pulled out
5370.800.002
5370.800.003
5370.800.004
5370.800.005
5370.800.006
5370.800.007
Zeichnung Nr.
drawing nr.
5370.800.001
Advertisement
Table of Contents
Related Manuals for Schlosser KB55S
Summary of Contents for Schlosser KB55S
- Page 1 Operating Instructions Safety Module Combination KB55S/SS-EB75GS EU-SG 374/EU-SG 735 / EU-SG 289 General Safety Module lk Progressive safety gear - upward/downward acting = payload + weight of lift car in FREE fall Braking device = 1/2 payload + masses UPWARDS upon tripping the overspeed governor incl. UCM/A3...
-
Page 2: General Instructions
Combination KB55S/SS-EB75GS General instructions !Important! Prior to commissioning: Before commissioning and testing the guide rails must be cleaned thoroughly prior to installation! Whether „old“ or „new“, (due to dirt, old lubricant or protective agents in case of new rails!), they must be kept clean both before and after commissioning!!! Should this not take place, negative changes in the braking force etc. -
Page 3: Mounting / Adjustment
Combination KB55S/SS-EB75GS Mounting / Adjustment opt.Swivel bar Double eccentric (8) High speed Brake shoe (10) Reversing lever (17) Actuation lever (22) Reset cam (19) opt. double reset clamp Actuation tab (23) High speed Release lever (24) Release bar (25) Brake shoe (1) - Page 4 Combination KB55S/SS-EB75GS D ( 0,20 : 1 ) Mounting / Adjustment / Check A ( 0,20 : 1 ) Setting type: EB 75 GS - acting upwards Adjust the braking device and guide rail using the adjusting screw (M6) until a clearance of 1 - 2 mm between the brake shoe (10) and the rail is set, then lock.
-
Page 5: Mounting Information
Felix-Wankel-Str.4, 85221 Dachau Tip: Gap between the switching part and release slider (5) Safety switch (27) approx. 5 – 10 mm! Type plate KB55S/SS Freewhell switcher (32) Air 0.5-1.00mm Air 0.5-1.00mm Make sure that the immersion depth of the rail is correct. - Page 6 Combination KB55S/SS-EB75GS Check Attention: Adjust the resetting spring in such a way that the pull-in forces are not too high and to ensure sufficient spring deflections. Clearance between the spring wires when fully opened Test in detail Reading DOWNWARDS: of marks...
-
Page 7: Liability And Guarantee
(Heavy counterweight to light cabin!). Liability and guarantee: The company Aufzugtechnologie Schlosser does not accept any liability or provide any guarantee for damages resulting from incorrect handling or inappropriate use of our products contrary to these instructions. - Page 8 Assembly of actuating gear KB55S/SS-EB75GS Reversing lever Lockwasher Releasing bolt Federring • Starting condition Auslöseschraube Switching cam Positioner sleeve Clip Clip opt. double reset clamp High speed Reversing lever Sicherungsstift Locking pin Lockwash Auslöselasche Actuating bar Releasing bolt Actuating bar...
Need help?
Do you have a question about the KB55S and is the answer not in the manual?
Questions and answers