Related Manuals for JetBlack Engine
Summary of Contents for JetBlack Engine
- Page 1 EURUSIII HVLS FAN INSTALL & USER MANUAL NZ Distributor of KaLe Environmental Technology (Shanghai) Corp. Web: www.kalefans.com...
-
Page 2: Table Of Contents
Table of Contents Introduction ................................2 About Jet Black Fan Systems ........................2 Our Products ................................2 SAFETY INSTRUCTIONS ..........................2 Recommended Safety Gear ........................4 What is in the packing case ........................4 Packing List ................................5 Equipment & Tools needed .......................... 5 Fan Diagram &... -
Page 3: Introduction
Jet Black Fan Systems HVLS Ceiling Fans efficiently help keep facilities and areas cooler in the summer and warmer in the winter. Jet Black Fan Systems HVLS Ceiling Engine or Eurus Fans are powerful, dependable and built to last for years to come. - Page 4 When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. c. The installation of an Engine or Eurus HVLS Fan must be in accordance with the requirements specified in this installation manual and with any additional requirements set forth by the NZECP, and all local codes.
-
Page 5: Recommended Safety Gear
The fan system you have purchased is for indoor use only unless otherwise specified by Jet Black Fan Systems. Do not expose fan to direct water contact. Improper use or handling of the Engine or Eurus HVLS Fan may cause damage or injury and will void the product warranty. -
Page 6: Packing List
Packing List Below is the list of items supplied with the Engine or Eurus HVLS ceiling fan. Note sizes of bolts may vary slightly on different models. Item Description Down rod Fan Blades (With Wingtips) Threaded Rods Fan Controller Motor... -
Page 7: Fan Diagram & Control Panel
Hardware to purchase: Description 1 tonne rate shackle with locking nuts 1 tonne rated eyebolt – for steel structure 1 tonne rated eye screw – for wooden structure only Metal sleeve – for wooden structure only 20m – 4.8mm 7 strand 700/800 tensile. See note below NOTE:: Check the length of cable required for the drop of the fan, needs to achieve 30-45degree angle –... -
Page 8: Preparing The Work Site
Preparing the Work Site IMPORTANT NOTE: Do not mount the fan to single purling, trusses, or bar joists. Mount the fan only to a structural element such as an H-beam, square tubing, concrete beam, or other load bearing structure. If large fan is being installed into a lightweight or timber structure it is recommended to have the structure checked by a structural engineer. -
Page 9: Install Appendix
e. Adhere to the safety requirements in the table below when selecting the fan location. The fan should be visible from the location of the wall controller. The mounting structure must be able to withstand the torque forces generated by the fan. Safety Requirement Minimum Distances Clearance... -
Page 10: Trouble Shooting And Error Codes
Fan System Layout Note it is best to connect to switchboard on a separate circuit, to ensure nothing else interferes with the fan. It is possible however to connect to a power point if necessary. Dedicated circuit on switchboard preferred 2.5 2 core plus earth 1.5 3 core plus earth... - Page 11 (1.1 Image) (1.2 Image) NOTE: Do not pull the motor wire with excessive force which may cause the wire to disconnect from the motor terminal. 2. Preparing the Mounting Assembly 2.1 Fix the mounting plate to the mounting structure using Clamping plates, Shims and M16 x 55mm hardware as shown in the figure below.
- Page 12 NOTES: Use proper lifting methods to prevent fan motor damage and personal injury. The approximate weight of the fan motor assembly is up to 95KG Do not tighten the bolts completely. Ensure that the motor wire is routed through the gap between the down rod and mounting plate.
- Page 13 4.1 Connect the wire rope links and turnbuckles to the holes on square block on the motor. 4.2 Making the Guy Cable Loop-1: Prepare Guy Wire Loop-1 at one of the guy cable using a Wire Thimble and three Wire Rope Clips. Install the first wire rope clip adjacent to the wire thimble followed by the second and third wire rope clips at 7.5cm - 9cm apart from each other.
- Page 14 4.4 Attach Eyebolt or Eyescrew to the mounting structure. The guy cable should be at 30 - 45° from the centre axis of the fan (see below illustration). Place the Eyebolt / screw accordingly. 4.5 Attaching Guy Cable Loop 2: Insert wire thimble into the 5/16” eye bolt and route the second end of the guy cable through the wire rope clips and wire thimble to make second Loop.
- Page 15 CAUTION: Over tightening of the guy cables may result in unbalanced fan. 4.8 Check the levelling of the fan motor to ensure that it is levelled. Levelling of the fan can be achieved by precisely adjusting the tension in all four guy cables by turning the Turnbuckles.
-
Page 16: Electrical Installation
Electrical Installation IMPORTANT NOTES Refer Safety Instruction on page 3 before proceeding. Exercise caution and common sense when powering the fan. Do not connect the fan to a damaged or hazardous power source. Do not attempt to resolve electrical malfunctions or failures on your own. Contact Jet Black Fan Systems if you have any questions regarding the electrical installation of this fan and register your fan product with Jet Black Fan Systems. -
Page 17: Maintenance
IMPORTANT NOTE: Power outage is prohibited during the fan normal operation. In case of a power failure and reversion, the Engine or Eurus HVLS ceiling fan system starts automatically as the power knob is still at RUN position. To prevent motor damage, ensure that the power switch is turned to STOP position in the event of a power failure. -
Page 18: Limited Warranty
Notes (name / company) Limited Warranty For Jet Black Fan Systems Industrial Engine and EurusIII Series HVLS Ceiling Fans Coverage The Limited Warranty covers the Engine and EurusIII Series brand of HVLS ceiling fans supplied by Jet Black Fan Systems. The warranty covers all standard fan parts and fan accessories found to have a manufacturing or workmanship defect. - Page 19 - Spare and replacement parts purchased by the Customer are not covered under this Limited Warranty. The Limited Warranty is transferrable to a new owner for the remaining period of the warranty. The warranty is transferrable to an end-user when the fan is purchased through a Jet Black Fan Systems authorized reseller, distributor or directly from Jet Black Fan Systems.
-
Page 20: Contact Information
Claim Process. If you experience any problem with the fan, immediately shut down fan operation and contact us so that we may help troubleshoot. In the event that the problem is not resolved over the phone, customer must a) file a claim, b) obtain an RMA #, c) package claimed part(s) appropriately to prevent any damage during handling and shipping,...