Enviro C Series Manual
Vertical belt drive blower coil units
Hide thumbs
Also See for C Series:
- Instruction manual (24 pages) ,
- Installation, operation and maintenance manual (32 pages)
Subscribe to Our Youtube Channel
Related Manuals for Enviro C Series
Summary of Contents for Enviro C Series
- Page 1 SERIES C VERTICAL BELT DRIVE BLOWER COIL UNITS INSTALLATION, OPERATION & MAINTENANCE Form ET115.24-NOM6 (0521) Supersedes: ET115.24-NOM6 (615) MODELS VB & VR...
-
Page 2: Table Of Contents
WARNING indicates a potentially NOTE is used to highlight additional hazardous situation which, if not information which may be helpful to avoided, could result in death or se- you. rious injury. ENVIRO-TEC... -
Page 3: Safety Considerations
Have prior to servicing to avoid burns. fire extinguisher available and ready for immediate use. Check that the unit assembly and com- ponent weights can be safely supported by rigging and lifting equipment. ENVIRO-TEC... -
Page 4: Pre Start-Up
ENVIRO-TEC. Violation will void warranty. If floor mount isolators are required, factory or field provisions must be made for isolator attachment. Units can be mounted directly to the floor or on a base rail. -
Page 5: Belts, Drives, And Bearings
A, AX 3.8 - 4.8" 1000 - 2500 5.0 - 7.0" 1000 - 2500 3.4 - 4.2" 860 - 2500 Not Recommended B, BX 4.4 - 5.6" 860 - 2500 10.5 5.8 - 8.6" 860 - 2500 12.6 LD13903 ENVIRO-TEC... -
Page 6: Replacement Parts
Replacement parts may be ordered from the local supported to ensure structural integrity and proper operation of the unit. ENVIRO-TEC representative. Factory replacement parts should be used wherever possible to maintain All water coils must be protected from agency listings. Should replacement parts not be freezing after initial filling with water. -
Page 7: Condensate Drain And Traps
NO BASE RAIL WITH BASE RAIL WITH BASE RAIL AND HOUSEKEEPING PAD Housekeeping pad Depending on static Required to accommodate pressure, housekeeping trap height pad may not be needed for trap installation LD13929 FIG. 2 - CONDENSATE DRAIN & TRAPS ENVIRO-TEC... -
Page 8: General Belt And Bearing Maintenance
Normal operation is based on 8 hours a day. If unit runs more than this, adjust accordingly RECOMMENDED TORQUE FOR TIGHTENING SETSCREWS Set Screw Diameter Minimum Recommended Torque Inch lbs. Foot lbs. 5/16 10.5 19.0 7/16 29.0 42.0 1104 92.0 LD13904 ENVIRO-TEC... -
Page 9: Motor Electrical Data
2. Discharge section includes a 2 row coil. MOTOR/DRIVE WEIGHT DATA MO TOR HP TYPE 1 1/ 2 SINGLE PHASE 37 [17] 37 [17] 45 [20] 47 [21] THREE PHASE 34 [15] 34 [15] 40 [18] 43 [20] 46 [21] 53 [24] 81 [37] LD13905 ENVIRO-TEC... -
Page 10: Model Vb Arrangements
3. Side access filter rack standard on arrangement 7 (Model VR). 4. Discharge heating coil section and supply plenum are not available with arrangement 7. 5. All drawings subject to change without prior notice. Refer to www.enviro-tec.com for current submittal drawings. LD13906... -
Page 11: Inspection & Start-Up Checklist
Verify Proper Heating Operation Reinstall All Covers & Access Panels Blower/Motor Check Sheave Set Screw Tightness Check Blower Wheel Set Screw Tightness Adjust Blower Speed as Necessary for Balancing Airflow Check/Adjust Sheave Alignment Check/Adjust Belt Tension LD13907 ENVIRO-TEC... -
Page 12: Dimensions
FORM ET115.24-NOM6 (0521) DIMENSIONS Model VB Basic Unit - Discharge Arrangement 2 52-80004REV01 ENVIRO-TEC... -
Page 13: Model Vb Basic Unit - Discharge Arrangement 1 With Blow-Thru Electric Heat
FORM ET115.24-NOM6 (0521) Model VB Basic Unit - Discharge Arrangement 1 with Blow-thru Electric Heat 52-80011REV01 ENVIRO-TEC... -
Page 14: Model Vr Basic Unit - Discharge Arrangement 2
FORM ET115.24-NOM6 (0521) Model VR Basic Unit - Discharge Arrangement 2 52-80007REV01 ENVIRO-TEC... -
Page 15: Model Vmr With Inlet Damper Section (Requires Base Rail) - Discharge Arrangement 2
FORM ET115.24-NOM6 (0521) Model VMR with Inlet Damper Section (Requires Base rail) - Discharge Arrangement 2 page 16 52-80020REV00 ENVIRO-TEC... -
Page 16: Inch Baserail Assembly
ALL DRAWINGS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DATE SHEET DRAWING NO DO NOT SCALE DRAWING ENVIRO-TEC DIMENSIONS ARE IN INCH [MM] FORMAT THIS DRAWING CONTAINS PROPRIETARY DATA. UNAUTHORIZED DISCLOSURE, 8/7/03 PAGE 1 OF 1 +/- 1/8 [3] UNLESS OTHERWISE NOTED... -
Page 17: Model Vb/Vr Discharge Plenum, Sizes 08-30
FORM ET115.24-NOM6 (0521) Model VB/VR Discharge Plenum, Sizes 08-30 VBR-003REV02 ENVIRO-TEC... -
Page 18: Model Vb Return Plenum, Sizes 08-30
FORM ET115.24-NOM6 (0521) Model VB Return Plenum, Sizes 08-30 52-80017REV00 ENVIRO-TEC... -
Page 19: Model Vb/Vr Discharge Section W/ Heating Coil, Sizes 08-30
FORM ET115.24-NOM6 (0521) Model VB/VR Discharge Section w/ Heating Coil, Sizes 08-30 VBR-004REV2 ENVIRO-TEC... - Page 20 ENVIRO-TEC is a registered trademark of Johnson Controls in the United States of America and other countries. Other trademarks used herein may be trademarks or registered trademarks of other companies. Catalog: ET115.24-NOM6 (0521) Supersedes ET115.24-NOM6 (615) © 2021 Johnson Controls P.O. Box 423, Milwaukee, WI 53201...
Need help?
Do you have a question about the C Series and is the answer not in the manual?
Questions and answers