Related Manuals for FloTech FT555 Series
Summary of Contents for FloTech FT555 Series
- Page 1 FloTech FT555 Series Automatic Truck Overfill System Tester Optic Systems Thermistor Systems Ground Bolt TIM Module 10784PA REV F Dixon Dixon Bayco Division Cincinnati, Ohio...
-
Page 2: Table Of Contents
FloTech FT555 Automatic Truck Overfill System Tester Table of Contents Table of Contents ................2 Introduction ..................3 Main Features.................. 3 FT555 Indicators ................5 Unpack Unit and Initial Setup............6 Welcome Screen ................7 Power On/Off .................. -
Page 3: Introduction
Read TIM modules and report serial number in display Verifying defective components Perform “WET TEST” to report when sensors are wetted To request an RGA for defective FloTech products under using integrated beeper. warranty. Configure auto test to perform all selected tests at once. - Page 4 FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Accessories Contact Flotech Customer Service (1-800-355-1991) or your local Flotech distributor for pricing and availability information on the following accessories. 1. FT556 – USA Test cable package This cable package is suited for use on systems in the US.
-
Page 5: Ft555 Indicators
FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester FT555 Indicators Step 5) The FT555 will repeatedly test for the presence of any wet sensors connected to the socket. A) LCD SCREEN Step 6) Dip test a compartment and listen for a number of beeps The LCD screen is the main display where test selection, test results, and corresponding to the compartment number that was dipped. -
Page 6: Unpack Unit And Initial Setup
FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Unpack Unit and Initial Setup Optic and Thermistor Wet Test Step 1) When unpacking the FT555 Automatic Truck Tester you will find the following: a) FT555 Automatic Truck Tester NOTE: THE WET TEST FUNCTION IS INTENDED TO BE b) Two “D”... -
Page 7: Welcome Screen
FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Welcome Screen After completing the Initial System Setup the welcome screen will Trailer ID Module Test be displayed. This screen will be displayed every time the FT555 Automatic Truck Tester is turned on. -
Page 8: Setup Instructions
FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Pin 9/10 Continuity Test Setup Instructions Pins 9 and 10 of the API socket will be tested for continuity and At the “Press Key” screen pressing the SETUP key will enter the the result of the test will be shown as PASS or FAIL on screen. - Page 9 FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester AutoTest Optic/Therm Ground Bolt Test Some regions may not have a need to test optic or thermistor type systems as none are found in that region. Example, trailers in...
- Page 10 FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Step 3) Press the ON/OFF button to turn on the FT555 Automatic Auto Test Ground Continuity System- OPTIONAL Truck Tester. When “Press Key” screen appears press “TEST SELECT”...
-
Page 11: Selecting Test Option
FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Step 5) Press the “TEST SELECT” button to move on to a new test, press “GO” to restart the test, or press the “ON/OFF” button Auto Test Truck ID Module- OPTIONAL to turn the tester off. - Page 12 FloTech FT555 Automatic Truck Overfill System Tester FloTech FT555 Automatic Truck Overfill System Tester Step 5) Press the “TEST SELECT” button to move on to a new test, press “GO” to restart the test, or press the “ON/OFF” button to turn the tester off.