Download Print this page

tell LC1200 Series Instruction Manual

Advertisement

Quick Links

INSTALLATION INSTRUCTION
LC1200/LC2400 SERIES LOCKS
HOW TO INSTALL THIS CYLINDRICAL LEVERSET
HOW TO INSTALL THIS CYLINDRICAL LEVERSET
HOW TO INSTALL A CYLINDRICAL LEVER SET
Leverset is set for 1 3 /
Leverset is set for 1 3 /4 " thick d oor - backset 2 3 / 4 "
LEVERSET IS SET FOR 1 3/4" THICK DOOR - BACKSET 2 3/4"
INSIDE
LEVER
DOOR HANDING
LEFT HAND
LEFT HAND
REVERSE
BEVEL
DOOR HANDS DETERMINED FROM OUTSIDE
1
DISASSEMBLE INSIDE LEVER
PUSH PIN
HOLE
INSIDE
LEVER
1A:
Insert push pin into hole to
depress catch and remove the lever.
Tell Manufacturing
hick d oor - backset 2 3 / 4
MOUNTING
INSIDE
SCREW
ROSE
INSIDE
SPRING CAGE
INSIDE
RIGHT HAND
OUTSIDE
INSIDE
RIGHT HAND
REVERSE
BEVEL
OUTSIDE
2
INSTALL LEVERSET TO DOOR
LATCH
2A:
Insert latchbolt and secure
with combination screws.
SCREW POSTS
REMOVABLE
THRU BOLTS
LOCK BODY
"
SLEEVE For 1 Hole
LATCH
COMBINATION
SCREW
STRIKE
LATCH
PRONGS
LATCH
2B:
Place lock body into position. Make sure
that latch prongs engage chassis in housing,
and slide engages latch tail.
1
OUTSIDE
LEVER
KEY
CYLINDER
ASSEMBLY
OUTSIDE
PUSH PIN
TRIM
New Door Preparation
1. Fold template over edge of
door and mark holes.
2. Drill a 2-1/8" hole.
3. Drill two 3/8" thru bolt holes
through face of door.(only if the
thru bolts are being used).
4. Drill a 1" hole in edge of door.
5. Cut 5/32" notches on
2-1/8" hole on both sides of door.
(very important if not using thr u bolts)
6. Mortise latch unit front
2-1/4" x 1-1/8" x 1/8" for 2-3/4" backset
or 2-1/4" x 1" x 1/8" for the optional 2-3/8" backset
LATCH
TAIL
SLIDE
INSIDE
SPRING
CAGE
LOCK
BODY
LOCK BODY
2C:
Install inside spring cage , Screws
should be hand tightened all the way down
with a screwdriver.
"
1 or 1-1/8
"
BASE
"
3/8
2 1/8"
-
1"
"
1/8
" or
"
-
2 3/8
-
2 3
/4
CENTER LINE
Align the joint
blade with line.
MOUNTING
SCREW
1-800-433-4047 | 020222

Advertisement

loading
Need help?

Need help?

Do you have a question about the LC1200 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for tell LC1200 Series

  • Page 1 Insert push pin into hole to should be hand tightened all the way down that latch prongs engage chassis in housing, with combination screws. with a screwdriver. depress catch and remove the lever. and slide engages latch tail. Tell Manufacturing 1-800-433-4047 | 020222...
  • Page 2 Remove the outside lever . body by screwdriver. lock body at both sides is symmetrical. outside rose tightly. Tell Manufacturing 1-800-433-4047 | 020222...
  • Page 3 1” Square For Scale Tell Manufacturing 1-800-433-4047 | 020222...

This manual is also suitable for:

Lc2400 series