Advertisement
Use only fasteners designed for electrical cable installations.
Inspect that the fastener has not damaged the insulation of the
electrical cables. A fastener that damages the insulation of electric
cables can lead to electric shock and fire hazards.
Do not use this nailer for fastening electrical cables. It is not
designed for electric cable installation and may damage the insulation
of electric cables thereby causing electric shock or fire hazards.
Additional safety warnings
The tool is designed for single-hand use. Do not hold the tool by the
front of the magazine. Do not put hands, head, or other parts of your
body near the bottom of the magazine where the nail exits the tool, as
serious personal injury could be caused.
Always ensure that the workpiece contact is fully positioned above
the workpiece. Positioning the workpiece contact only partially above
the workpiece could cause the nail to miss the workpiece completely
and result in serious personal injury.
Do not drive nails near edge of material. The workpiece may split
causing the nail to ricochet, injuring you or a coworker. Be aware
that the nail may follow the grain of the wood, causing it to protrude
unexpectedly from the side of the work material or deflect, possibly
causing injury.
Keep hands and body parts clear of immediate work area. Hold
workpiece with clamps when necessary to keep hands and body out
of potential harm. Be sure the workpiece is properly secured before
pressing the fastener against the material. The workpiece contact
may cause the work material to shift unexpectedly.
Keep face and body parts away from back of the tool cap when
working in restricted areas. Sudden recoil can result in impact to the
body, especially when nailing into hard or dense material.
During normal use the tool will recoil immediately after driving
a fastener. This is a normal function of the tool. Do not attempt to
prevent the recoil by holding the nailer against the work. Restriction
to the recoil can result in a second fastener being driven from the
nailer. Grip the handle firmly, let the tool do the work and do not place
second hand on top of tool or near exhaust at any time. Failure to
heed this warning can result in serious personal injury.
Do not drive fasteners on top of other fasteners or with the tool at an overly
steep angle as this may cause deflection of fasteners which could cause injury.
Always check the work area for hidden wiring, gas lines, water lines,
etc., before using the product on such work area.
After using the product in the contact actuation mode, switch it back
to the full sequential mode.
The driving depth of the nail may be adjusted beyond air pressure. It
is advisable to test the depth on a scrap workpiece to determine the
required depth for the application.
Only fasteners matching the description in the product specifications
table can be used with this tool. Using incorrect fasteners may lead to
jamming or other malfunctions.
Always remove the battery before adjusting the depth of drive.
Do not press the trigger while adjusting the depth of drive.
Always select full sequential firing mode before adjusting the depth
of drive.
Do not point the tool towards yourself or anyone nearby when
adjusting the depth of drive.
The product will restart automatically if stalled. Switch off the product
immediately if it stalls. Do not switch on the product again while it
is still stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the product stalled and rectify this,
paying heed to the safety instructions.
Ambient temperature range for tool during operation is between 0°C
and 40°C.
Ambient temperature range for tool storage is between 0°C and 40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
Wear ear protectors. Exposure to noise can cause hearing loss.
Clamp workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
Sawdust and splinters must not be removed while the product is
running.
When working in walls, ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the product.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System AEG chargers for charging System AEG battery
packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately seek
medical attention.
Ambient temperature range for tool during operation is between 0°C
and 40°C.
Ambient temperature range for tool storage is between 0°C and 40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
Before first use, test the nailer function with scrap wood. This
will ensure correct performance of the nailer. If the nailer
experiences performance issues, re-inflate the air tank following
the instructions given.
SPECIFIED CONDITIONS OF USE
The nailer is intended to drive nails in soft materials such as wood.
This product is not suitable for fixing electric cables.
Do not use the product for any other purpose.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and
19
19
Advertisement
